Eagle G920D Manual Download Page 2

IMPORTANT

Installer and Users please note:

These instructions should be read carefully and left with the user of the product for 

future reference.

Before Use

You must inspect  the product  for  any signs of damage. If the product is damaged, 

DO NOT use it, and contact your supplier immediately.

General Safety Requirements

Domestic wiring must  be  tested  periodically by a  qualified electrician  at  least  once 

every 10 years or at every change of occupancy.

For office and retail premises, and buildings such as village halls, the wiring must be 

inspected at least once every 5 years.

It is recommended that all building be  fitted with smoke alarms (it  is mandatory for 

new buildings).

Product Safety

The G920D must be installed by a competent electrician in accordance with the 

current IEE wiring regulations.

This  appliance  can  be  used  by  children  aged  from  8  years  and  above  and  

persons    with  reduced  physical,  sensory  or  mental  capabilities  or  lack  of 
experience  and  knowledge  if  they  have  been  given  supervision  or  instruction 
concerning use of the appliance in a safe way and understand the hazards involved. 

Children shall not play with the appliance. 

Cleaning  and  user  maintenance  shall  not  be  made  by  children  without 

supervision.

For indoor use only.

Do  not  use  or  install  this  appliance  in  the  immediate  surroundings  of  a  bath, 

shower or swimming pool.

Do  not  use  or  install  this  appliance  in  locations  where  paint,  petrol  or  other 

flammable liquids are used or stored.

G920D User Guide

 - page 2 -

Summary of Contents for G920D












Reviews: