Eagle G920D Manual Download Page 11

SERVICE WARRANTY

Electrovision  guarantees  the  product  free  from  defects  in  materials  and 

workmanship for a period of twelve months.

Should  this  appliance  be  operated  under  conditions  other  than  those 

recommended, at  voltages other than the  voltage indicated on  the appliance, or any 
attempts made to service or modify the appliance, then the warranty will be rendered 
void.

The product you buy may sometimes differ slightly from illustrations. This warranty 

is in addition to, and does not affect, your statutory rights.

Our guarantee is administered by our retailers.
If  your  product  arrives  damaged,  you  must  contact  the  retailer  from  whom  you 

bought  it.  The  retailer's  contact  details  will  be  on  the  invoice  that  arrived  with  the 
product,  or  on  the  e-mail  you  received  when  you  placed  the  order.  Do  not  contact 
Electrovision, only your retailer can arrange a replacement.

If the product

 

needs to be repaired or replaced, you must contact the retailer from 

whom you bought it.

The retailer's contact details will be on the invoice that arrived with the product, or 

on the e-mail you received when you placed the order.

If you have  just  received your product  and require  technical help in  using  it, please 

call our Help Desk on (0845) 459 4816

If you have any other technical queries about the product, please call our Help Desk 

on (0845) 459 4816.

Electrovision Ltd.,

Lancots Lane, Sutton,

St. Helens, Merseyside.

WA9 3EX

website: www.electrovision.co.uk

G920D User Guide

- page 11 -

Summary of Contents for G920D












Reviews: