Eachine E160 User Manual Download Page 7

Turn on the helicopter after

binding successfully, the

propeller rotate constantly

but the helicopter can not

take off. 

Problem

Cause

Solution

Low charge in aircraft

batteries or main

gear loose.

Replace and charge the

batteries ; press the

spindle with gear tightly. 

5

6

7

8

9

10

11

12

13

Helicopter power is turned

supreme speed govermor

electric sound

Damaged frotor blades

and lateral axis

blade grips too tight

causing the movement

of the main rotor isn't

smooth.

Reference helicopter 6G

mode setting

Helicopter vibrates or

shakes in flight.

Main rotor blades are

shaking in flying.

The sound of the main

rotor becomes smaller.

Helicopter has no

reaction or can not

fly smoothly.

3D/6G model helicopter

appeared yaw

Helicopter yaw occurs in 6G

mode,

Helicopter took off spin

to the left.

Check the connectors replace

speed governor

Brushless speed governor

fault or poor contact

Check with the tail rotor blades

and the motor shaft,If loose

replacement tail rotor blade.

Motor damage Replace the

tail motor.

Tail motor power shortage

loose blades

Tail motor damage

Helicopters hover need to

reconfigure

Swashplate servos not back

in to mid-position or damage

Failure of binding

Low battery voltage

of helicopter.

Lateral axis is bent

Latreral axis screw is not

tight .There are some

debris in the servo,

causing shakes .

The loose between the

swashplates.

Deformed or damaged t

ail rotor blades.

Change the main rotor

blades, and lateral axis

Loosen the blade grips

properly.

Replace the lateral axis.

Tighten the lateral axis

screw. Change the

Bearing.

Remove the servo, and

clear debris.

Compress the

swash plates.

change the tail rotor

blades.

Charge the battery or

change a fully charged

battery.

Rebind the helicopter

and transmitter, make

sure you place the

helicopter static level

next to the transmitter.

Length adjustment rod,

so thatthe vertical spindle

swashplate

Replace the servo

EXPLODED VIEW 

- 10 -

- 11 -

Summary of Contents for E160









Reviews: