Eachine E160 User Manual Download Page 4

1. The user should connect  to the power adapter with a USB 
   port or connect to the USB port of computer.
2. Connect the USB cable to the power adapter, at the same
    time the USB charger red light flashes.
3. The partial voltage charging head of the battery is connected 
    with the USB cable. At this time, the USB charger's red light 
    always on and charging is in progress.
4. When the USB charger red light is off, charging is completed.

HELICOPTER PARAMETERS

Length
Height
Weight
Length of Main Propeller
Diameter of Tail Propeller
Battery Specification
Flight Time
Main Brushless Motor
Brushless Tail Motor

345 MM
108MM
156g
350MM
62.5MM
7.4v 700mah 25C
5-6 Min
1312
1103

WARNING AND THE GUIDE OF BATTERY USAGE

To ensure safety, please use the icluded standard charger

WARNING:

 It is recommended to use the original power supply charger when charging, 

                otherwise property damage and injury will occur.

Notice:

 When it is lower than 7.4V, the lithium battery may be damaged, or it may no longer 

           be charged. When the battery voltage is lower than 7.4V when the aircraft is flying, 
           the power of the aircraft drops significantly. Please immediately land and charge the 
           battery in time.

BATTERY CHARGING 

7.4 700mAh

Warning

1. To ensure safety, please charge under the supervision of someone.
2. Children cannot charge alone, they should charge with the assistance of an adult.
3. Please use the original standard charger of this product for charging. The charger of
    unknown origin may cause a fire and explosion accident.
4. It is recommended that users prepare their own 2A current adapter, which will shorten
   the charging time.

1.  Make sure the battery power is full both for TX and helicopter.
2. Before open the power of TX, please make sure the TH. Stick at the bottom and the 
    switch of TH.HOLD and 3D mode in back position (back cover direction).
3. Make sure the TX has paired with helicopter ,or please pair them again.
4. Please open TX first, then connect the battery with the RX board on helicopter to pair 
    with TX. When close, please cut the power of helicopter first, and then turn off the TX.
5. Keep away from crowd, cars, high-tension towers and pond. Then you can start your 
   flying.

NOTICE BEFORE FLIGHT

You buy the original model The pairing has been reset before factory. If you need to pair 
again, please comply with the following steps.
1. First open the remote control, make sure the throttle joystick is in the bottom position,
   3D1 IDLE switch in the OFF position
2. Take down the canopy for touching the code switch.
3. Charge the helicopter, the red lamp flashes slowly, press the code button for 1 second,
    then the red lamp will go out and get ready for pairing.
4. When the red and blue lights turn solid, the pairing has been successful.
5. Ensure  there  are  no  other  remote  controllers  of  the  same  type  at  work  to  avoid
    interference.

Tips:

 This product is compatible with all FUTABA 2.4GHZ S-FHSS remote controller.

Notice:

 If the throttle of the transmitter has not been positioned at the lowest position

          with the throttle switch and 3D mode switch turned on, the transmitter will beep 
          to prompt you that it fails to proceed to pair.

PAIR THE TRANSMITTER WITH THE RECEIVER

- 4 -

- 5 -

Summary of Contents for E160









Reviews: