E2S A100 AlertAlarm, Instructions/Service Manual

Page: 7 / 12

E2S Warning Signals
Impress House, Mansell Road, Acton, London W3 7QH sales@e2s.com e2s.com D218 - 00 - 001 - IS - UL Issue A 26/04/2021
FIRE INSTRUCTION & SERVICE MANUAL
A100 Range AlertAlarm Sounder UL464 / CAN/ULC - S525
Model: A100DC
•
- 40°C to +66°C / - 40°F to +151°F
•
Units can be mounted using the 2 - off ø6mm holes in the mounting lugs or through the back of the housing using the supplied gasket
seal.
•
A100DC024 is approved for use as an audible signal appliance for fire alarm use – Public Mode (UL464 & CAN/ULC - S525) and produc-
es a minimum sound pressure level of US: 79.55dB(A); CA: 85.2dB(A) at 10 feet, (figures @ worst case 10Vdc).
•
At 24Vdc the A100DC024 produces a minimum sound pressure level of US: 88.52dB(A); CA: 93.7dB(A) at 10 feet
•
For Fire Alarm applications, the Sounder Volume must be at the highest setting, (see volume control section). For fire alarm use, Tone
12 as shown below must be selected:
•
Connection Terminals: Pluggable
AC: 1.0 - 2.5mm
2
/ AWG18 - AWG12
DC: 0.2 - 2.5mm
2
/ AWG24 - AWG12
•
Terminal Tightening torque 0.4Nm
•
To maintain Ingress Protection, cable entries must be fitted with suitably rated cable glands or stopping plugs
•
Units can be located indoor or outdoor wet use, wall or ceiling mounted and there are no limitations on orientation
•
Factory finishes are not intended to be modified
Surge Current Ratings for use in fire alarm systems
Model Nominal Voltage Voltage Range Initial Peak Initial RMS
A100DC024 24V dc 10 - 60V dc 298mA 56.4mA
A100DC024 Sounder Directional Characteristics for Canadian Fire CAN/ULC - S525 at 10 feet
Horizontal Axis Vertical Axis
Angle OSPL Angle OSPL Angle OSPL Angle OSPL
Ref. 90° 92.6 dB(A) Ref. 90° 92.6 dB(A) Ref. 90° 93 dB(A) Ref. 90° 93 dB(A)
149° - 3 dB(A) 32° - 3 dB(A) 148° - 3 dB(A) 33° - 3 dB(A)
153° - 6 dB(A) 28° - 6 dB(A) 151.5° - 6 dB(A) 29° - 6 dB(A)
180° 87.2 dB(A) 0° 87 dB(A) 180° 87.2 dB(A) 0° 86.4 dB(A)
Attention: Installation must be carried out by an electrician in compliance with the National Electrical Code, NFPA 70, and the National Fire Alarm
Signaling Code, NFPA 72 or CSA 22.1 Canadian Electrical Code, Part I, Safety Standard for Electrical Installations, Section 32. / L'installation doit
exclusivement être réalisée par du personnel qualifié, conformément au code national d'électricité américain, NFPA 70, et le code national d
’ alarrme
incendie et de signalisation NFPA 72 ou CSA 22.1 Code canadien de l'électricité, première partie, norme de sécurité relative aux installations électriques,
Section 32
Attention: Disconnect from power source before installation or service to prevent electric shock / Débranchez - le de la source d'alimentation avant l'instal-
lation ou l'entretien pour éviter tout choc électrique.
Attention: Do not paint / Ne pas Peinturer
+ + - - S2 S3
S2 S1
1000Hz(0.5s on, 0.5s off)x3 + 1s gap ISO 8201 Temporal
Pattern
Stage 1
Set DIP
SW 1
Tone No.
Tone Description Tone Visual
Stage 1 & 2
DIP SW 1/2
Settings
1 2 3 4 5 6
Stage 3
Set DIP
SW 1
(S3)
Stage 4
Set DIP
SW 1
(S2 + S3)
12 1 1 0 1 0 0
1000Hz 0.5s
0.5s
0.5s
0.5s
0.5s
1s
1 8