manualshive.com logo in svg

E-Seek 200, Programming Manual, Page: 9 / 16

Share
Download
E-Seek 200 Programming Manual Download Page 9

- 9 - 

Prefix / Suffix Setup 

Description:

 To setup prefix and suffix parameters, changes will be effective after 

scanner ACK response. 

Host Requirement:

 To setup prefix and suffix with a control characters use the following 

table: 

[NUL] [SOH] [STX] [ETX] [EOT] 
[ENQ] [ACK] [BEL] [BS]  [HT] 
[LF]  [VT]  [FF]  [CR]  [SO] 
[SI]  [DLE] [DC1] [DC2] [DC3] 
[DC4] [NAK] [SYN] [ETB] [CAN] 
[EM]  [SUB] [ESC] [FS]  [GS] 
[RS]  [US]  [DEL] 

Example:

 setting suffix with AbC, Carriage Return and Line Feed is 

“SOH”<SUFFIX=AbC[CR][LF]>” EOT” 

Then, the suffix value is added to the end of every good read, the control characters are 
sent in ASCII characters. 

Code Identifier: 

If the code identifier is enabled, then the standard AIM ID is added to 

the prefix.  The AIM ID values are the following: 

Code39 

  ]A 

Code128 

  ]C 

PDF417 

  ]L 

Magnetic 

  ]M 

The Code identifier is added to the end of the prefix value. 

Scanner Response:

  ACK / NAK 

 

Description 

Field 

Values allowed 

Prefix 

Set 

PREFIX= 

Add Code Identifier 

Enable  

PRECID=1 

Disable * 

PRECID=0 

Suffix 

Set 

SUFFIX= 

Add CR to Suffix 

Enable 

SUFFCR=1 

Disable * 

SUFFCR=0 

Table 2.4 

 

Summary of Contents for 200

















Reviews:

No comments