manualshive.com logo in svg

E-Seek 200, Programming Manual, Page: 13 / 16

Share
Download
E-Seek 200 Programming Manual Download Page 13

- 13 - 

NO-READ Message Setup 

Description:

 To setup No-Read parameters, changes will be effective after scanner 

ACK response. 

The scanning results of a no read card are the following: 

Magnetic Stripe (M250/260):

 

If there is a problem in reading a recorded information on 

a track, the reader reports error using the ASCII string “

NR

” (HEX 45 & 52) for each 

track.   

If there is no recorded information on a track, the reader reports an error using the ASCII 
string “

ND

” (HEX 45 & 44) for each track. 

Any enabled prefixes or suffixes are appended around this message. 

Linear Barcode:

 

If there is a problem in reading a 1D (code39 or Code 128) on the 

card,  The reader reports an error using t

he ASCII string “

NR0

” (HEX 45 & 52 & 30).  

Any enabled prefixes or suffixes are appended around this message.  The reader does 
not send the Code ID even in case that the option is enabled.   

PDF417 Barcode:

 

If there is a problem in reading a PDF417 on the card, the reader 

reports an error using the ASCII string “

NR

” (HEX 45 & 52) followed by a character 

indicating a type of error.  The error types are: 

“

0

” : Not found a PDF417 symbol 

“

1

” : Too many damaged code-words 

“

2

” : Too many Misread code-words 

“

3

” : Codeword translation to ASCII error 

Any enabled prefixes or suffixes are appended around this message. The reader does 
not send the Code ID even in case that the option is enabled. 

Scanner Response:

  ACK / NAK 

 

Description 

Field 

Values allowed 

No-Read Message 

Enable  

NOREAD=1 

Disable * 

NOREAD=0 

Table 2.12 

 

Summary of Contents for 200

















Reviews:

No comments