E-Mu SP-12 Owner'S Manual Download Page 36 | Manualshive

Page: 36 / 99

background image

RECORDING SEGMENTS

© E-mu Systems, Inc. 1985

Page 36

Enhanced by The Emulator Archive 2002 www.emulatorarchive.com

2K ADDING SWING

While in segment mode, you may specify that a segment have a particular rhythmic
swing to it. The SP-12 defaults to a “swing factor” of 50%, which means that each
quarter note is weighted so that the first eighth note takes up 50% of the quarter
note, and the second eighth note takes up the other 50%. This is the way you would
normally expect things to be.

However, you may change the swing factor to 514%, 58%, 63%, 67%, or 71%. For
example, with a swing factor of 58%, the first eighth note spreads out slightly to take
up 58% of the quarter note, while the second eighth note shrinks slightly so that it
takes up 142% of the quarter note. This lets you program a swinging, less
metronomic feel to individual segments.

To program a segment for swing, you must be in segment mode. Then, follow these
steps:

1. The SP-12 must be stopped (RUN/STOP light off). Press SWING.

2. The display shows the current swing setting for the selected segment. The

Right Arrow and Left Arrow buttons step through the various swing options.

3. When the display shows the desired swing value, press ENTER.

Notes:

Swing can help add a more human “feel” to a series of repeating segments.

For example, if you repeat the same segment four times, try setting a swing factor of
514% for, say, the third segment. This results in a series of segments that are more
psycho-acoustically interesting than merely repeating the same pattern over and
over.

67% is considered the “classic” jazz swing factor, where the first eighth note is 2/3 of
a quarter note, and the second eighth note is 1/3 of a quarter note (i.e. the second
eighth note behaves more like an eighth note triplet). If this sounds too “perfect”, try a
swing factor of 64% instead. The results will be similar, but the “feel” will be slightly
different.

If you’re trying to record or erase in a segment that has a swing factor other than
50%, there are two cautions. To erase a specific note, you have to erase where the
note would normally occur If the segment had a 50% swing factor. If you record while
a segment is in swing mode, the beats may or may not fall where you want them to
fall. Therefore, it’s best to go out of swing mode when recording or erasing, then re-
enter swing mode after you’ve finished your alterations.

«
...
34
35
36
37
38
...
»

Summary of Contents for SP-12




































































































Reviews:

No comments

Related manuals for SP-12

Brand: Shakmat Pages: 9

Brand: FAS International Pages: 136

Brand: Delptronics Pages: 23

Brand: Alesis Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands