background image

Manual SCA-SE-30-06 

V 0.9 

10/02    page 12 

 

e-motion Gesellschaft für Antriebstechnik mbH, Zettachring 2, D-70567 Stuttgart, Germany 
Tel.: +49-(0)711-7221535, Fax.: +49-(0)711-7221548 E-mail: [email protected]

 

9.  Commissioning 
 

9.1.  Selection of power supply 

Any power supply can be used as long the minimal requirements listed below are fulfilled. We 
recommend to remove the motor from the mechanical construction to avoid damage and danger by 
uncontrolled movements. 
 
Requirements to the power supply: 
Output voltage:  

min. 11 V DC max. 30 V DC 

Residual voltage: 

< 5 % 

Output current:   

6 A nominal. 

 
 

9.2.  Function of the potentiometers 

Potentiometer  Function 

Turning ccw 

Turning cw 

 

 

 

 

Gain 

Gain adjustment 

Decreasing 

Increasing 

N max 

Maximum speed at set value of 
10 V 

Decreasing speed 

Increasing speed 

I max 

Current limitation 

Decreasing min. 0 A 

Increasing max. 6 A 

I x R 

none 

 

 

Offset 

adjustment n=0 at set value= 0 

Motor turns cw 

Motor turns ccw 

 
 

9.3.  Presetting of potentiometers 

Original delivered servo amplifiers are adjusted to uncritical values and for easy adjustment by the 
user. 
 

9.4.  Adjustment 

1.   Adjust max. set value (e.g. 10 V) and turn potentiometer 

n max

 cw til the 

required speed is reached 

2.  Adjust potentiometer

 Imax 

to required value of current limitation. 

Important

: Refer to motor manufacturers data sheet 

3.  Turn potentiometer 

Gain

 slowly cw until the required gain is reached 

Important: If the motor turns rough, is vibrating or makes noise turn 
potentiometer ccw again, until  the instability of the system is obsolete.  

4.  Adjust set value = 0 V and adjust potentiometer 

Offset 

until the motor stops 

to speed 0. 

DC-Tacho control 
Digital-Encoder control  
 

 

 

 
 
9.5.  Commissioning 

Select the required operating mode by setting the according jumpers on the left side of the unit. Refer 
to the printing on the front plate. Required selection of: 

• 

operating mode 

• 

Input for set value 

• 

Maximum input frequency of encoder 

Connect motor, control inputs e.g. set value, enable and an additional encoder to the drive. 
Connect power supply. 
Enabling and adjustment referring to manual. 

Summary of Contents for SCA-SE-30-06














Reviews: