manualshive.com logo in svg

E-Mon D-Mon, Installation Manual, Page: 23 / 26

Share
Download
E-Mon D-Mon Installation Manual Download Page 23

9.0  

Display Screens

The Green Class Net Meter cycles through eight (8) separate display screens.  
These screens are described in further detail below.

Screen 1 - kWh Delivered

 

   

 

 

This screen displays the amount of energy    

 

   

 

 

(kWh) delivered from the serving 

   

 

  utility/energy 

provider.

 

 

Screen 2 - kWh Received

 

   

 

 

This screen displays the amount of energy

 

   

 

 

(kWh) received by the serving 

 

   

 

 

utility/energy provider.  It shows the energy

 

   

 

 

that was pushed back into the electrical grid

 

   

 

 

from excess capacity in a building with a

 

   

 

 

cogeneration, solar or wind powered supply

   

 

  system.

Screen 3 - Net (Delivered minus Received)

 

   

 

 

This screen displays the Net reading of both

 

   

 

 

the delivered and received energy.  In this

 

   

 

 

example, the received amount (2 kWh) is

 

   

 

 

subtracted from the delivered amount (7

 

   

 

 

kWh).  If more energy is received into the 

 

   

 

 

electrical grid this can be a negative number.

Screen 4 - Not Utilized

 

   

 

 

This screen is not utilized at this time.

Screen 5 - Real-Time Net Load in kW

 

   

 

 

This screen displays the “real-time” Net

 

   

 

 

load in kW (Kilowatts.)  It indicates the 

 

   

 

 

present load of this service.

Screen 6 - Not Utilized

 

   

 

 

This screen is not utilized at this time.

 

Page 20

Summary of Contents for D-Mon



























Reviews:

No comments