E-matic PMWS2W Manual Download Page 1

 

 

PMWS2W 

SURFACE MOUNT 2-WIRE WALL 
SWITCH 

 

 Main Body 

 PIR Sensor / Red LED / Photocell Sensor 

 Slide Switch 

 

INTRODUCTION

 

The  PMWS2W  110  degrees  Surface  Mount  2-Wire 
Wall  Switch  is  a  fully  automatic  indoor  controller 
capable  of  controlling  up  to  2000W  incandescent 
lightings.  It  has  been  specifically  designed  to  replace 
manually  operated  light-switches  in  so  called  2-wire 
installation.  It  adopts  16A  bistable  relay  of  which 
nature is high switching power and longer expected life 
for electrical and uses a passive infrared (PIR) motion 
sensor  which  reacts  to  changes  in  temperature 
emitted  by  the  motion  of  persons  or  objects  passing 
through its detecting area.    When you enter the room, 
it  turns  on  automatically  the  light  to  which  it  is 
connected and the light remains lit as long as the wall 
switch senses any activity in the room.    It however will 
automatically turn off the light after the  preset  turn-off 
time is expired.    During the day, the built-in photocell 
sensor  saves  electricity  by  deactivating  the  light.   
When  turning  to  AUTO  position,  the  sensor  will  draw 
power  from  the  battery  and  constantly  monitor  the 
battery voltage; whereas it is also a must to connect to 
AC  mains  supply,  providing  power  source  to 
connected light fixture when motion has been detected. 
Please  take  note  that  it  is  an  automatic  light  switch 
which cannot be used in intrusion applications. 
 
It  is  a  very  handy  device,  which  affords  you  safety, 
security,  convenience  and  energy  saving.    It  is  also 
easy to install and is suitable for the following places: 
living  room,  family  room,  stairway,  entryway,  garage 
and driveway etc. 
 
With  this  wall  switch  installed,  you  get  rid  of  the 
nuisance of fumbling in a dark hallway or staircase for 
a  light  switch,  thus  avoiding  danger  for  the  elderly, 

infirm and children at night or when it is dark. 

 
Note: Read this entire manual before you start to 
install the system. 

 

SAFETY PRECAUTIONS

SAFETY PRECAUTIONS

SAFETY PRECAUTIONS

SAFETY PRECAUTIONS

 

 

 

Be  sure  to  switch  off  power  source  before 
installing. 

 

Make  sure  that  the  power  wiring  comes  from 
circuit  with  an  external  miniature  circuit  breaker 
not higher than 16A for the short circuit protection 
or a suitable fuse. 

 

The unit cannot be installed on the ceiling. 
(FIGURE 1) 

 
 
 
 
 
 

FIGURE 1 

IMPORTANT 

Installation must be performed by a skilled/competent 
person who is familiar with the appropriate standards 
and  technical  requirements  of  the  appliance  and  its 
proper installation. 
 
Before  proceeding  with  the  installation,  TURN  OFF 
THE POWER TO THE LIGHTING CIRCUIT AT THE 
CIRCUIT  BREAKER  OR  FUSE  BOX  TO  AVOID 
ELECTRICAL SHOCK.

    

 

CHOOSING A MOUNTING LOCATION

CHOOSING A MOUNTING LOCATION

CHOOSING A MOUNTING LOCATION

CHOOSING A MOUNTING LOCATION

 

 

 

For the best results, fix your sensor on a solid 
surface, at least 1.7m above the ground. 

 

For indoor installation, a location under eaves is 
preferable. 

 

Avoid aiming the motion sensor at pools, heating 
vents,  air  conditioners  or  objects  which  may 
change temperature rapidly. 

 

Do not allow sunlight to fall directly on the front of 
unit.     

 

Try to avoid pointing the unit at trees or shrubs or 
where the motion of pets may be detected. 

 

The  motion  sensor  is  more  sensitive  to  objects 
moving  across  its  field  of  view.    It  is  less 
sensitive to an object moving directly towards the 
sensor head. (FIGURE 2) 

       

Reviews: