E-FLITE Tensor 4D Assembly Manual Download Page 3

Page: 3 / 48

Additional Tools and Adhesives

Tools

Square

Hobby knife

Ruler

T-pin

Razor saw

Drill bit: 1/16", 1/8"

Drill

Small Phillips screwdriver

Motor/Gearbox

E-flite™ Park 370 Outrunner, 1080KV

Propeller: 10x4.7

Adhesives

Foam-safe CA

Servo tape

Thin CA

Warning

An RC aircraft is not a toy! If misused, it can cause

serious bodily harm and damage to property. Fly

only in open areas, preferably at AMA (Academy of

Model Aeronautics) approved flying sites, following

all instructions included with your radio.

Additional Required Equipment

Recommended JR® Systems

Servos: JR 241 Sub-micro servo (3)

Receiver: JR R610M 6-channel micro FM Rx or R610UL

Radio: JR 4-channel system

Battery and Speed Control Requirements

Li-Po Battery: 7.4V 860 2-Cell

Speed Control: 10 amp brushless

Summary of Contents for Tensor 4D

















































Search results

Summary of Contents for Tensor 4D

Reviews:

Related manuals for Tensor 4D

Brands by name

Popular brands

E-FLITE Tensor 4D, Assembly Manual

Search results

Summary of Contents for Tensor 4D

Reviews:

Related manuals for Tensor 4D

Brands by name

Popular brands