background image

5

E-flite Pitts Model 12 15e ARF Assembly Manual

Notes Regarding Servos and ESC

WARNING

: Use of servos other than those we recommend may 

overload the BEC of the recommended Electronic Speed Control 

(ESC). We suggest the use of only the servos we recommend 

when utilizing the recommended ESC’s BEC, or the use of a 

separate BEC (like the UBEC) or receiver battery pack when 

using other servos.

Note on Lithium Polymer Batteries

Lithium Polymer batteries are significantly more 

volatile than alkaline or Ni-Cd/Ni-MH batteries used 

in RC applications. All manufacturer’s instructions 

and warnings must be followed closely. Mishandling 

of Li-Po batteries can result in fire. Always follow the 

manufacturer’s instructions when disposing of Lithium 

Polymer batteries.

Warning

An RC aircraft is not a toy! If misused, it can cause serious 

bodily harm and damage to property. Fly only in open areas, 

preferably at AMA (Academy of Model Aeronautics) approved 

flying sites, following all instructions included with your radio.
Keep loose items that can get entangled in the propeller away 

from the prop, including loose clothing, or other objects such as 

pencils and screwdrivers. Especially keep your hands away from 

the propeller.

Warranty Period

Horizon Hobby, Inc., (Horizon) warranties that the Products 

purchased (the “Product”) will be free from defects in materials 

and workmanship at the date of purchase by the Purchaser.

Limited Warranty

(a) This warranty is limited to the original Purchaser 

("Purchaser") and is not transferable. REPAIR OR REPLACEMENT 

AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE 

REMEDY OF THE PURCHASER. This warranty covers only those 

Products purchased from an authorized Horizon dealer. Third 

party transactions are not covered by this warranty. Proof of 

purchase is required for warranty claims. Further, Horizon 

reserves the right to change or modify this warranty without 

notice and disclaims all other warranties, express or implied.
(b) Limitations- HORIZON MAKES NO WARRANTY OR 

REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-

INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A 

PARTICULAR PURPOSE OF THE PRODUCT. THE PURCHASER 

ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED 

THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS 

OF THE PURCHASER’S INTENDED USE.
(c) Purchaser Remedy- Horizon's sole obligation hereunder  

shall be that Horizon will, at its option, (i) repair or (ii) 

replace, any Product determined by Horizon to be defective. 

In the event of a defect, these are the Purchaser's exclusive 

remedies. Horizon reserves the right to inspect any and all 

equipment involved in a warranty claim. Repair or replacement 

decisions are at the sole discretion of Horizon. This warranty 

does not cover cosmetic damage or damage due to acts of 

God, accident, misuse, abuse, negligence, commercial use, 

or modification of or to any part of the Product. This warranty 

does not cover damage due to improper installation, operation, 

maintenance, or attempted repair by anyone other than 

Horizon. Return of any goods by Purchaser must be approved 

in writing by Horizon before shipment.

Summary of Contents for Pitts Model 12 15e ARF





































Reviews: