background image

6

E-flite Enticement F3P Profile Assembly Manual

Damage Limits

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT 

OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR 

PRODUCTION OR COMMERCIAL LOSS IN ANY WAY 

CONNECTED WITH THE PRODUCT, WHETHER SUCH CLAIM IS 

BASED IN CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT 

LIABILITY. Further, in no event shall the liability of Horizon 

exceed the individual price of the Product on which liability 

is asserted. As Horizon has no control over use, setup, final 

assembly, modification or misuse, no liability shall be assumed 

nor accepted for any resulting damage or injury. By the act of 

use, setup or assembly, the user accepts all resulting liability.
If you as the Purchaser or user are not prepared to accept the 

liability associated with the use of this Product, you are advised 

to return this Product immediately in new and unused condition 

to the place of purchase.
Law: These Terms are governed by Illinois law (without regard to 

conflict of law principals).

Safety Precautions

This is a sophisticated hobby Product and not a toy. It must be 

operated with caution and common sense and requires some 

basic mechanical ability. Failure to operate this Product in a safe 

and responsible manner could result in injury or damage to the 

Product or other property. This Product is not intended for use 

by children without direct adult supervision. The Product manual 

contains instructions for safety, operation and maintenance. It is 

essential to read and follow all the instructions and warnings in 

the manual, prior to assembly, setup or use, in order to operate 

correctly and avoid damage or injury.

Questions, Assistance, and Repairs

Your local hobby store and/or place of purchase cannot provide 

warranty support or repair. Once assembly, setup or use of the 

Product has been started, you must contact Horizon directly. 

This will enable Horizon to better answer your questions and 

service you in the event that you may need any assistance. 

For questions or assistance, please direct your email to 

[email protected], or call 877.504.0233 toll 

free to speak to a service technician.

Inspection or Repairs

If this Product needs to be inspected or repaired, please call for 

a Return Merchandise Authorization (RMA). Pack the Product 

securely using a shipping carton. Please note that original boxes 

may be included, but are not designed to withstand the rigors 

of shipping without additional protection. Ship via a carrier that 

provides tracking and insurance for lost or damaged parcels, as 

Horizon is not responsible for merchandise until it arrives and 

is accepted at our facility

. A Service Repair Request is available 

at www.horizonhobby.com on the “Support” tab. If you do not 

have internet access, please include a letter with your complete 

name, street address, email address and phone number where 

you can be reached during business days, your RMA number, 

a list of the included items, method of payment for any non-

warranty expenses and a brief summary of the problem. 

Your original sales receipt must also be included for warranty 

consideration. Be sure your name, address, and RMA number 

are clearly written on the outside of the shipping carton.

Warranty Inspection and Repairs

To receive warranty service, you must include your original 

sales receipt

 verifying the proof-of-purchase date. Provided 

warranty conditions have been met, your Product will be 

repaired or replaced free of charge. Repair or replacement 

decisions are at the sole discretion of Horizon Hobby.

Summary of Contents for Enticement F3P





































Reviews: