manualshive.com logo in svg

E-FLITE Blade CP Pro 2, Manual, Page: 5 / 40

Share
Download
E-FLITE Blade CP Pro 2 Manual Download Page 5

8

9

Battery Charging

It is important that you only charge the included 3S 11 .1V 800mAh LiPo Battery Pack (EFLB0996) with the 
included 3S 11.1V LiPo Balancing Charger (EFLC3105). Your battery pack is equipped with special Charge 
Protection Circuitry and a Balance Charge Lead with Connector that is only compatible with this charger . 
Attempting to charge the pack using another LiPo charger or non-LiPo compatible charger could result in serious 
damage . Please familiarize yourself thoroughly with the Battery Warnings and Guidelines section before continuing .

The included 3S 11 .1V LiPo Balancing Charger will charge a near fully discharged (not over-discharged) 3S 11 .1V 
800mAh LiPo Battery Pack in approximately 1.2–1.5 hours. In some cases the charge time may be shorter 
depending on the actual amount of capacity left in the pack after a flight . NEVER charge the battery unattended .

Note:

 

The LiPo battery pack included with your Blade CP Pro 2 will arrive partially charged . For this reason the 

initial charge may only take approximately 30–50 minutes.

The charger requires up to 1.5 amps of 11.5–15 volts of DC input power that can be supplied by the optional AC 
to 12V DC, 1 .5-amp Power Supply (EFLC4000) for convenient charging anywhere an AC outlet is available . NEVER 
attempt to power the charger from an AC outlet without the use of a proper AC to DC adapter/power supply .

Note:

 

When using the AC to DC adapter/power supply, the charger is protected to prevent damage if the alligator 

clips touch . However, please take care to ensure that the alligator clips do not cause shorting of the battery, 
adapter/power supply, etc . by keeping them clear .

Input power for the charger can also be supplied from a small 12V gel cell or car battery . 

The charger is equipped with two LED indicators marked RED and GREEN on the label . These LEDs indicate the 
following (also found on the label of the charger):
• Red Flashing LED Only: Input power with no battery connected
• Red and Green Solid LED: Battery connected and charging
• Red Solid LED Only: Charge complete

• Red and Green Flashing LED: Charge error

Once you have connected the charger to a power source (use care to ensure proper polarity when connecting 
the charger to the power source), its red LED will flash to indicate the charger has power and is ready to begin 
charging . Connect the LiPo battery pack to the charger using the specially marked Balance Charge Lead exiting 
the battery pack and the connector labeled with 11 .1V on the charger . The connector is keyed to prevent reverse 
polarity connection .

When the battery is properly connected and charging normally, the red and green LED indicators will glow solid . 
Once the battery has been fully charged, the green LED will go out, leaving just the red LED glowing solid . The 
battery can now be removed from the charger and installed into the Blade CP Pro 2 for flight .

Summary of Contents for Blade CP Pro 2









































Reviews:

No comments