manualshive.com logo in svg

E-FLITE AT-6 25e Texan ARF, Assembly Manual, Page: 28 / 52

Share
Download
E-FLITE AT-6 25e Texan ARF Assembly Manual Download Page 28

28

E-flite AT-6 Texan ARF Assembly Manual

Fixed Landing Gear Installation

Required Parts

Wing center section 

Landing gear (right and left)

1/8-inch wheel collar (4) 

3mm x 4mm machine screw (2)

3mm x 10mm self-tapping screw (8)

Required Tools and Adhesives

Drill 

Drill bit: 5/64-inch (2mm)

Thin CA 

File

Phillips screwdriver: #1, #2 

Pencil

Threadlock

Note

: The main wire struts included with your kit have 

been upgraded from the preproduction versions shown 

in this manual. Please note your wire struts will have the 

main wire yoke offset as per the real AT-6 landing gear.



  1. Position the main gear on the rails of the wing center 

section. Use a pencil to transfer the locations for the four 

mounting screws through the gear and onto the rails.



  2. Use a drill and 5/64-inch (2mm) drill bit to drill the 

four holes for the mounting screws. Use care not to 

accidentally drill through the top of the wing.



  3. Apply a few drops of thin CA to each of the holes to 

harden the surrounding wood.

Summary of Contents for AT-6 25e Texan ARF





















































Reviews:

No comments