CONVENTIONAL FEATURES
36
PARMS” and then rotate that switch to display the
desired parameter. Then press the Select switch again
to select it.
SCAN TIMER -
Selects the Scan Hold timer.
Rotate the Select switch to decrement/increment
the timer in 0.5-second steps (“0” disables it).
When the desired value is displayed, store it by
pressing the Select switch.
TX TIMER -
Selects the transmit time-out timer.
Rotate the Select switch to decrement/increment
the timer in 15-second steps (“0” disables it). When
the desired value is displayed, store it by pressing
the Select switch.
PEN TIMER -
Selects the penalty timer. Rotate
the Select switch to decrement/increment the timer
in 15-second steps (“0” disables it). When the
desired value is displayed, store it by pressing the
Select switch.
CONV TIMER -
Selects the conversation timer.
Rotate the Select switch to decrement/increment
the timer in 30-second steps (“0” disables it). When
the desired value is displayed, store it by pressing
the Select switch.
5.16.7 CHANNEL PARAMETERS
NOTE: If
“PASSWORD”
is briefly displayed when
attempting to select a parameter, see Section 5.16.3.
The “CHAN PARMS” menu parameter selects
the following conventional channel parameters that
can be reprogrammed. Press Select switch to select the
“CHAN PARMS” parameter and then rotate that
switch to display the desired parameter. Then press the
Select switch again to select it. The squelch control
parameters are unique to the type of conventional
channel selected (analog or Project 25).
NOTE: If a mixed mode channel is selected, both the
Rx Code (analog) and Rx NAC (P25) can be
programmed. In addition, if the Tx Type is Analog, a
Tx Code is programmed, and if it is Digital (P25), a Tx
NAC is programmed.
RX FREQ -
Programs the receive channel frequency.
To select the digit to change or move the cursor to the
right, press the Select switch. Then to display the
desired digit, rotate the Select switch. The frequency is
stored after programming the last digit. If an invalid
frequency is entered, a beep sounds, “INVALID” is
briefly displayed, and the frequency editing mode
continues to be selected.
TX FREQ -
Selects the transmit frequency the same
the preceding RX FREQ.
CTCSS/DCS Squelch Control (Analog Channel)
RX CODE -
Sets the receive Call Guard (CTCSS/
DCS) code. Rotate the Select switch to select the
desired type (CTCSS and DCS). Then press and
rotate the Select switch to select the desired code.
The displayed code is stored after the last digit is
programmed. If an invalid code is entered, a beep
sounds, “INVALID” is briefly displayed, and the
editing mode continues to be selected.
TX CODE -
Selects the transmit codes the same as
RX CODE above.
NAC Squelch Control (Project 25 Channel)
RX NAC -
Selects the Network Access Code
(NAC) which can be any number from 0-4095.
Rotate and press the Select switch to enter the
desired code. The displayed code is stored after the
last digit is programmed. If an invalid code is
entered, a beep sounds, “INVALID” is briefly
displayed, and the NAC editing mode continues to
be selected.
TX NAC -
Selects the transmit NAC the same as
RX NAC above.
TX POWER -
Selects the desired power output level.
Rotate the Select switch to scroll through the
following choices. When the desired setting is
displayed, store it by pressing the Select switch.
•
POWER HI - High transmit power
•
POWER LO - Low transmit power
•
POWER SW - Switchable power selectable by
the High/Low power switch. This choice is not
available if that switch is not programmed.
TX TIMER -
Enables or disables the time-out timer
on the current channel. Rotate the Select switch to
toggle between the on and off mode, and when the
