OPERATION
2-19
September 2001
Part No. 001-5100-001
3. Press the PTT switch to initiate the call. The display
then indicates the alias of the destination radio. If
the entered digits do not correspond to a valid list
entry, “INVALID” is displayed and an error tone
sounds. Proceed to the bulleted list following the
next method for other conditions that may occur
next.
Direct Entry Method (Full Keypad Models Only)
1. With a SMARTNET/SmartZone channel selected,
press and hold the Private Call option switch until a
tone sounds (approximately 1 second). The last ID
called is displayed.
2. Using the 0-9 keys, enter the ID (all six digits) of the
mobile unit you are calling. To erase the last digit,
press the
key, and to cancel the call, press the
CLR
key.
3. Press the PTT switch to initiate the call. If the
entered ID did not contain six digits, “INVALID” is
momentarily displayed, an error tone sounds, and
the call is not initiated. If the entered ID is valid, the
display indicates the alias of the ID if it matches an
ID in your call list. Otherwise, the ID you entered
continues to be displayed. Any of the following
conditions may then occur:
•
If the radio you are calling is on the air, “WAIT” is
displayed and telephone type “ringing” is heard
for 20 seconds or until the called party answers.
•
If the called party answers and the call is
successful, the person’s voice is heard and the call
is carried on the same as a group call. To end the
call at any time, press the
CLR
key.
•
If the called party does not answer within 20
seconds, “NO ANS” is displayed and a continuous
tone sounds. End the call by pressing the
CLR
key.
•
If the called radio is not in service, no ringing is
heard, “NO ACK” is displayed, and a continuous
tone sounds. End the call by pressing the
CLR
key.
•
If neither your radio nor the radio being called is
authorized to make unit-to-unit calls, “REJECT”
is displayed and a continuous tone sounds. End the
call by pressing the
CLR
key.
•
If the called party answers but the radio system is
busy, four low tones sound and “BUSY” is
displayed. When the system is no longer busy, the
call back tone sounds.
•
If in the secure mode and your transceiver does not
have the proper encryption key, “KEYFAIL” is
displayed and the call must be made in the clear
mode (selected by the Clear/Secure option switch
if enabled on the channel).
•
If an out-of-range condition exists or the radio
system is not in service, “LOST CALL” is
displayed and a continuous tone sounds. End the
call by pressing the
CLR
key.
Receiving an Enhanced Private Conversation Call
These calls are automatically received if a
SMARTNET/SmartZone channel is selected. Proceed
as follows:
1. When a call is received, a recurring unit call tone
(three beeps) sounds for up to 20 seconds and
“CALL” is displayed.
2. To answer the call, press the Private Call option
switch and then the PTT switch and begin talking.
The alias of the incoming call is displayed if the ID
is in your call list. Otherwise, the unit ID is
displayed.
NOTE: If the Private Call option switch
is not pressed before the PTT switch, a group call is
transmitted on the selected group.
•
To end the call when the conversation is complete
or at any other time, press the
CLR
key.
•
If unit-to-unit (private) calls are not permitted
(Private Call switch not programmed), press the
Call Response option switch, if available, to
answer the call.
•
If the call is not answered within 20 seconds, it is
automatically terminated.
•
If the radio system is busy, four low tones sound
and “BUSY” is displayed. When the system is no
longer busy, the call back tone (four beeps) is
heard and your radio automatically starts transmit-
ting. Press the PTT switch to continue the call.
