background image

16

User Manual EE600 Differential Pressure Sensor

Volume flow measurement

Unit: m

3

/h, m

3

/s, ft

3

/min, l/s

Layout: one line with limit bar or two lines (volume flow and differential pressure) without limit bar.

Air velocity measurement

Unit: m/s, ft/min

Layout: one line with limit bar or two lines (air velocity and differential pressure) without limit bar.

Filter monitoring

Unit: %

Layout: one line with limit bar or two lines (filter monitoring and differential pressure) without limit bar.

Level indicator

Unit: cm, inch

Layout: one line with limit bar or two lines (level indicator and differential pressure) without limit bar.

Examples of display visualisation

15.0

mbar

919.0

Pa

7580

m³/h

Fig. 12 

Display with one line with limit bar and two lines without limit bar

5.4  PCS10 Product Configuration Software

Only available with analogue version with auto-zero and digital version.

For performing adjustment or changes in EE600 settings, please proceed as follows: 
1. Download the PCS10 Product Configuration Software from 

www.epluse.com/pcs10

 and install it on 

the PC.

2.  Connect the EE600 to the PC using the USB configuration adapter. 

3.  Start the PCS10 software. 

4.  Follow the instructions on the PCS10 opening page for scanning the ports and identifying the 

connected device.

5.  Click on the desired setup or adjustment mode from the main PCS10 menu on the left and follow the 

online instructions of the PCS10

6.  Refer to the tutorial available throughout PCS10.

PC

HA011066

Service interface connector

Fig. 13 

EE600 configuration and adjustment

Please note:

 The EE600 may not be connected to any additional power supply when using the USB 

configuration adapter HA011066.

Summary of Contents for EE600























Reviews: