background image

V-3000 PLUS / V-4000 PLUS Front & Rear View

depth 445 mm

Front

height

88mm

Front width  483mm

Figure

 

1

page 3

V-3000 PLUS  /  V-4000 PLUS

P R O F E S S I O N A L    P O W E R    A M P L I F I E R

Introduction

Congratulations on your purchase of a new V PLUS Series professional power amplifier, and thank you for your 
confidence in DynaTech products. 

For your safety, please read the Important Precautions section before installing and operating the amplifier.

The DynaTech V PLUS Series is based on the same advanced circuit topologies that have made DynaTech 
amplifiers the choice of touring professionals worldwide. V PLUS Series amplifiers are designed for high 
operating efficiency and accurate sonic performance across the full audio bandwidth, even under stressful 
conditions.  Internal components are the finest available, and key sub-assemblies are pre-tested before final 
assembly. Finally, each amplifier is "burned in" and thoroughly tested (using precision audio test equipment) 
before shipping. In addition, all V PLUS Series amplifiers incorporate DynaTech’s exclusive Tour Class 
protection features to safeguard both internal circuitry and connected loudspeakers. This proven combination 
of advanced design, quality construction, and comprehensive circuit protection is your guarantee of fail-safe 
reliability. You can depend on consistent, stable performance even when your V PLUS Series amplifier is 
subjected to punishing extremes in the most demanding fixed or mobile sound reinforcement applications.

Unpacking

Please inspect the amplifier carefully immediately after unpacking. If you find any damage, notify your 
supplier/dealer immediately. Only the shipper may file a damage claim with the carrier for damage incurred 
during shipping. Be sure to save the carton and all packing materials for the carrier's inspection. If your packing 
materials are in good condition, please save them. If you ever need to ship the unit back to DynaTech or an 
authorized service center, you should use only the original factory packing.

Installation and Mounting

V PLUS Series amplifiers is 2-rack-space units. Mount in standard 19-inch racks. Four front-panel mounting 
holes are provided on each amplifier. Rear mounting ears give additional support, and use of rear supports is 
highly  recommended  in all mobile and touring sound systems. Optional rack-mount handles are available.

Front Views & Rear Views Introduction

  |  

  |  Front Panel 

 |

  Rear Panel  |  SET UP  |  Operation Mode  |  Protection  |  Specifications

Summary of Contents for V PLUS Series















Reviews: