143
F80W
D451198B
1
3
2
451120
STOP
12V
0V
14V
D452025
11
13
12
STOP
12V
0V
14V
24
D452024
WORKSHOP MANUAL
13�7�4 Test of burner ignition
When testing the burner ignition, check the behaviour of the
burners and the position of the gas flame.
The behaviour of the burners when ignited is correct if the burn-
ers ignite within a few seconds.
Unless the burners ignite within a few seconds, the ignition box
stops further attempts for igniting the burners and interrupts
gas supply.
Burner ignition test procedure
Open the access to the burners.
Insert the key into the ignition box (11) in the position “0” and
switch over to the position “I”.
Set the key between position “I” and “II” and the engine glowing
indicator lamp (24) will light up.
Do not perform engine glowing for more than 15 s.
Use the alarm horn (12) to signal that the engine is starting.
Start the engine by turning the key to position “II”.
Secure the screed against free fall.
Set the maximum paving width on both sides of the machine.
Turn the key in the ignition box (11) from position “II” to position
“I”. The engine switches off.
Switch on the gas screed heating system by moving the switch
(13) to the upper position.
Check that all burners are burning.
Unless the burners start within a few seconds, switch off the gas
screed heating system and perform a test of spark plugs, or have
spark plug maintenance performed. Have the test and mainte-
nance of spark plugs performed by an authorised service plant
or qualified personnel according to the procedure given below.
Visually check the gas flame position on all burners (1). Perform
the visual check through the burner pipe (2) and check their po-
sition with regard to the spark plug (3).
If the gas flame is incorrect, have the flame position adjusted.
Have the flame position adjustment performed by an author-
ised service or qualified personnel according to the procedure
given below.
Switch off the gas screed heating system by moving the switch
(13) to the lower position.
Close the access to the burners.
Set the key between position “I” and “II” and the engine glowing
indicator lamp (24) will light up.
Do not perform engine glowing for more than 15 s.
Use the alarm horn (12) to signal that the engine is starting.
Start the engine by turning the key to position “II”.
Set the minimum paving width on both sides of the machine.
Unlock the screed and lower it to the ground.
Turn the key to the position “0” and remove the key from the
ignition box (11).
Summary of Contents for Hatz F80W
