Dynamix RC 903-V35FE1 User Manual Download Page 17 | Manualshive

Page: 17 / 26

Dynamix RC 903-V35FE1 User Manual Download Page 17

5

th

bit: sending side ‘TX-grounded;

6

th

bit: receiving side ‘RX-grounded;

7

th

bit: impedance adjustment at the receiving side

8

th

bit: impedance adjustment at the sending side

Attention: Set according the above table, or else the E1 interface will be abnormal.

4.4. Inside Jump pin definition

When the user want to adjust the internal jump pin, please do it under the guidance or
agreement of Dynamix technical engineer. Usually it is not necessary; unless it is in
sever environment or disturbance.
After opening the case, you can see two groups of Jump pin (JP2 and JP3) on the
upper layer of the circuit board. Its position, order of pin and default configuration is as
follow:

Definition of Jump pin:

JP2

1:PGND protection

ground

2:BNC_GND BNC screened layer
3:GND working

ground

The default setting is 1-2 pins short-circuited.

JP3

1:PGND protection

ground

2:GND working

ground

3:NC No

definition

The default setting is 1-2 pins short-circuited.

16

«
...
15
16
17
18
19
...
»

Summary of Contents for RC 903-V35FE1



























Reviews:

No comments