4
3 - LIThIUM DISChArgINg
1. Connect the banana plugs of the battery adapter cable to the
Power Output Black (–)
and
Power Output Red (+)
, making sure that the positive and negative connectors are not reversed.
2. Connect the JST_XH balance adapter to the
Balance Circuit Adapter Board Connector
.
3. Connect the battery connector to the battery adapter cable.
4. Connect the balance connector of the battery to the JST_XH balance adapter.
5. Press the
Left
and
Right Arrows
on the
LCD Touch Screen
to scroll through the main menu
screens until you reach Program Select=Li-Po/Li-Ion/Li-Fe.
Program select=LiPo
LiPo
CHG
DCHG
STOR
6. Press
DCHG
.
LiPo DISCHARGE
Pack.Volt. : 7.4V/2S
Capacity : 2250mAh
Current : 0.5A
End Cell Volt :
3.49V
Press&Hold : DISCHRG
BACK
SELECT
7. Press a parameter to highlight that parameter.
8. Press the
Up
and
Down Arrows
to edit the parameter.
9. Press
Select
to save the parameter.
10. Once the parameters are at the desired settings, press and hold
DISCHRG
.
11. The charger will check the battery and charger settings and discharging will begin. The
charger will beep and display the following screen:
LiPo DCHG
000:30S
Capacity : 13mAh
Current : 1.4A
Voltage : 7.91V
Resistance : ****mΩ
Peak Temp.
:
No sens
12. Press the
arrow
in the top right of the
LCD Touch Screen
to see the rest of the Discharging
information.
13. Press
Unit
to see the voltages for each cell. Press
Back
to return to the discharging screen.
DATA LiPo–CELLS
1 > 3.97
2 > 3.98
3 > 0.00
4 > 0.00
5 > 0.00
6 > 0.00
BACK
14. Press
Graph
to see the battery voltage graph. Press
Back
to return to the discharging screen.
Data LiPo = Graph
BACK
15. Press
STOP
at any time to stop discharging.
16. When discharging is complete, the charger will sound a series of beeps and display the
following screen:
LiPo DONE
010:28S
Capacity : 169mAh
Current : 0.0A
Voltage : 8.00V
Resistance : ****mΩ
Peak Temp.
:
No sens
17. Disconnect the battery from the charger.
1. Connect the banana plugs of the battery adapter cable to the
Power Output Black (–)
and
Power Output Red (+)
, making sure that the positive and negative connectors are not reversed.
2. Connect the JST_XH balance adapter to the
Balance Circuit Adapter Board Connector
.
3. Connect the battery connector to the battery adapter cable.
4. Connect the balance connector of the battery to the JST_XH balance adapter.
5. Press the
Left
and
Right Arrows
on the
LCD Touch Screen
to scroll through the main menu
screens until you reach Program Select=Li-Po/Li-Ion/Li-Fe.
Program select=LiPo
LiPo
CHG
DCHG
STOR
6. Press
STOR
.
LiPo STORAGE
Pack.Volt. : 3.7V/1S
Capacity : 50mAh
Current : 0.1A
End Cell Volt :
3.70V
Press&Hold :
STORE
BACK
SELECT
7. Press a parameter to highlight that parameter.
8. Press the
Up
and
Down Arrows
to edit the parameter.
9. Press
Select
to save the parameter.
10. Once the parameters are at the desired settings, press and hold
STORE
.
11. The charger will check the battery and charger settings and storage charging will begin. The
charger will beep and display the following screen:
LiPo STORE
000:11S
Capacity : 4mAh
Current : 1.8A
Voltage : 7.87V
Resistance : ****mΩ
Peak Temp.
:
No sens
12. Press the
arrow
in the top right of the
LCD Touch Screen
to see the rest of the storage
Charging information.
13. Press
Unit
to see the voltages for each cell. Press
Back
to return to the storage charging screen.
DATA LiPo–CELLS
1 > 3.97
2 > 3.98
3 > 0.00
4 > 0.00
5 > 0.00
6 > 0.00
BACK
14. Press
Graph
to see the battery voltage graph. Press
Back
to return to the storage charging screen.
Data LiPo = Graph
BACK
15. Press
STOP
at any time to stop charging.
16. When charging is complete, the charger will sound a series of beeps and display the following
screen:
LiPo DONE
010:28S
Capacity : 169mAh
Current : 0.0A
Voltage : 8.00V
Resistance : ****mΩ
Peak Temp.
:
No sens
17. Disconnect the battery from the charger.
4 - LIThIUM STOrAgE ChArgINg
