3
PrOgrAMMINg qUICk gUIDE
1. Press the
Left
and
Right Arrows
on the
LCD Touch Screen
to scroll through the
main menu screens.
2. Press the action at the bottom of the
LCD Touch Screen
to enter that menu.
3. Press a parameter to highlight that parameter.
4. Press the
Up
and
Down Arrows
to edit the parameter.
5. Press
Select
to save the parameter.
6. If there is more than one screen of parameters, press the top right corner of the
LCD Touch
Screen
to scroll through the parameter screens.
7. Press
Back
to return to the main menu screens.
When the charger is powered ON, there is a series of self tests and the screen will show the
charger brand name and model number.
OPErATINg YOUr ChArgEr
CAUTION:
If at any time during the charge process the battery pack becomes hot or begins to puff disconnect the battery immediately and discontinue the charge process as batteries can
cause fire, collateral damage and injuries.
CAUTION:
Using a charge rate that is not compatible with the battery capacity may result in damage or malfunction of the charger or battery.
CAUTION:
The Lithium charge program menus are to be used ONLY for the charging and discharging of Lithium battery packs. Charging other battery types using the Lithium charge programs
will damage the battery or the charger.
1 - SELf TEST AND PrOgrAM SELECT SCrEENS
1. Connect the banana plugs of the battery adapter cable to the
Power Output Black (–) (A)
and
Power Output Red (+) (B)
, making sure that the positive and negative connectors are not
reversed.
2. Connect the JST_XH balance adapter to the
Balance Circuit Adapter Board Connector (C)
.
3. Connect the battery connector to the battery adapter cable.
4. Connect the balance connector of the battery to the JST_XH balance adapter.
5. Press the
Left
and
Right Arrows
on the
LCD Touch Screen
to scroll through the main menu
screens until you reach Program Select=Li-Po/Li-Ion/Li-Fe.
Program select=LiPo
LiPo
CHG
DCHG
STOR
6. Press
CHG
.
LiPo CHARGE
Pack.Volt. : 11.1V/3S
Capacity : 1050mAh
Current : 1.0A
End Cell Volt :
4.20V
Press&Hold : CHARGE
BACK
SELECT
7. Press a parameter to highlight that parameter.
8. Press the
Up
and
Down Arrows
to edit the parameter.
9. Press
Select
to save the parameter.
10. Once the parameters are at the desired settings, press and hold
CHARGE
.
11. The charger will check the battery and charger settings and charging will begin. The charger
will beep and display the following screen:
LiPo CHG
000:11S
Capacity : 11mAh
Current : 4.0A
Voltage : 8.00V
Resistance : ****mΩ
Peak Temp.
:
No sens
12. Press the
arrow
in the top right of the
LCD Touch Screen
to see the rest of the Charging
information.
13. Press
Unit
to see the voltages for each cell. Press
Back
to return to the charging screen.
DATA LiPo–CELLS
1 > 3.97
2 > 3.98
3 > 0.00
4 > 0.00
5 > 0.00
6 > 0.00
BACK
14. Press
Graph
to see the battery voltage graph. Press
Back
to return to the charging screen.
Data LiPo = Graph
BACK
15. Press
STOP
at any time to stop charging.
16. When charging is complete, the charger will sound a series of beeps and display the following
screen:
LiPo DONE
010:28S
Capacity : 169mAh
Current : 0.0A
Voltage : 8.00V
Resistance : ****mΩ
Peak Temp.
:
No sens
17. Disconnect the battery from the charger.
2 - LIThIUM (LI-PO/LI-fE/LI-ION) ChArgINg
Only Li-Po is shown in the following three sections. Li-Ion/Li-Fe menus differ ONLY in Cell and Pack Voltage values.
