Dynamatic CES, Instruction Manual, Page: 29 / 38

29
Special DMR Parameter and Fault Number Reference Chart for DMR with Stop-On-Bottom Feature Table 3-4
PARAMETER PARAMETER PARAMETER PARAMETER
NUMBER NUMBER
00 Not Used 72 No. Of Speed Feedback Periods
01 Average Speed Feedback - SPM 73 Serial Interface Baud Rate
02 Speed Reference - SPM 74 Under-speed % Limit
03 Average Speed Error (+/-) - SPM 75 Die Contact Angle
04 Effective Resolver Position 76 Resolver Direction Selection
05 AC Line Voltage - Volts 77 Resolver Offset Angle
06 Not Used 78 Gear Ratio
07 Not Used 79 Pulses per Rev.
08 Clutch Current Feedback - Amps 80 Pot. Selector
09 Brake Current Feedback - Amps 81 Stop-On-Bottom Creep Speed Angle - DEG
10 EPROM 82 Stop-On- Bottom Apply Brake Angle - DEG
11 Part Number 83 Creep Speed-Bottom - SPM
12 Speed at Die Contact Angle - SPM FAULT NUMBER FAULT
13 Serial Interface Data Received 0101 Over-speed
14 Analog Speed Reference 0202 Loss of Tach
15 Average Parts per Minute 0208 Clutch Current Delay
16 Clutch Current Timer - SEC 0206 Press Movement in Wrong Direction
17 Brake Current Timer - SEC 0207 Loss of Line
18 CL-BR Coil Cool Down - SEC 0208 Enable without Clutch On
19 Under-speed Timer - SEC 0209 Cl. Contactor On After Cl. On De-energized
20 Over-speed Timer - SEC 0210 Missing Enable
21 Not Used 0211 Inch + Micro Inch + Enable
22 Actual Resolver Position 0212 Reverse Command
23 Main Program Loop Ctr. 0220 Enable Present After Normal Stop
24 Present Pr. Fault Codes 0221 Clutch Contactor Not On in Test Mode
25 Previous Pr. Fault Codes 0222 Press Movement in Test Mode
26 Max. Pr. Run Sp. – SPM 0223 Enable Present in Test Mode
27 Max AC Line Voltage 0224 Stop-On-Top Not Performed
28 Max. Cl. Cur. Scaling Factor – Amps 0225 Cl. Contactor On Removed w/o Removing
29 Max. Br. Cur. Scaling Factor – Amps Enable or During 450 ms Time Delay
30 Angle 1 - DEG 0226 Clutch Contactor On w/o Enable
31 Speed 1 - SPM 0227 Enable Before Cool Down Expired
32 Angle 2 - DEG 0228 Creep Sp. Not Reached Before Stop Angle
33 Speed 2 - SPM 0313 Under-speed
34 Angle 3 - DEG 0314 Clutch and Brake Current Overlap
35 Speed 3 - SPM 0315 Clutch Current
36 Angle 4 - DEG 0316 Brake Current
37 Speed 4 - SPM 0317 Inch Change
38 Angle 5 - DEG 0318 Micro Inch Change
39 Speed 5 - SPM 0319 Reverse Change
40 Angle 6 - DEG 0329 Parameter Out of Limits
41 Speed 6 - SPM SIGNALS FOR CHART
42 Stop-On-Top Creep Sp. Angle - DEG RECORDER
43 Stop-On-Top Apply Br. Angle - DEG TERMINAL FUNCTION
44 Creep Speed-Top - SPM 337 Common
45 Micro Inch Speed - SPM 338 Speed Reference
46 Inch Speed - SPM 339 Clutch Current
47 Inch Accel Rate – SPM/SEC 340 Brake Current
48 Initial Accel Step – SPM 341 Speed Feedback
49 Initial Accel Rate – SPM/SEC FAULT INDICATOR
50 Run Accel Rate 1 – SPM/SEC NUMBER FAULT
51 Run Accel Rate 2 – SPM/SEC - Run Signal is Present
52 Run Accel Rate 3 – SPM/SEC 0 Push Reset
53 Run Accel Delta 1 – SPM/SEC 1 External
54 Run Accel Delta 2 – SPM/SEC 2 Brake Free Wheel
55 Run Decel Rate 1 – SPM/SEC 3 Low Line
56 Run Decel Rate 2 - SPM/SEC 4 Brake Over-current
57 Run Decel Rate 3 - SPM/SEC 5 Clutch Free Wheel
58 Run Decel Delta 1 – SPM/SEC 6 Line/Microprocessor
59 Run Decel Delta 2 – SPM/SEC 7 Clutch Over-current
60 Test Mode
61 Clutch Test Mode
62 Brake Test Mode
63 Clear Faults
64 Cl. Cur. On too Long Timer - SEC
65 Br. Cur. On too Long Timer - SEC
66 Cl/Br Coil Cool Down Timer - SEC
67 Under-speed Timer - SEC
68 Over-speed Timer - SEC
69 % Over-speed - %
70 Wrong Direction Limit - DEG
71 Display Update Time - SEC