manualshive.com logo in svg

Dynacraft Realtree, Owner'S Manual

Share
Download
Dynacraft Realtree Owner'S Manual Download Page 15

14

9.  ROOF REAR SUPPORTS 

ASSEMBLY

•  Find the Rear Support marked with an 

“R” and attach it to the corresponding U 
shaped support also marked with an “R”.
Use two 4x12 mm round head screws to 
secure the supports, as shown at right.

•  Find the other Rear Support, marked with 

an “L” and attach it to the corresponding 
U shaped support also marked with an “L”. 
Use two 4x12 mm round head screws to 
secure the supports as shown at right.

4x12 

Round 

Head 

Screw

4x12 Round 

Head 

Screw

Roof Rear 

supports

“R” Mark

“L” Mark

10. ROOF ASSEMBLY 

INSTALLATION

•  Insert the Front and Rear roof supports 

into the four corresponding holes in the 
ride-on toy body as shown in diagram 1.

•  Secure each of the Front Roof Supports 

using a 4x16 mm round head screw on 
each side, as shown in diagram 2.

•  Secure each of the Rear Roof Supports 

using two 4x16 mm round head screws on 
each side, as shown in diagram 3.

4x16 Round 

Head Screw

Rear Roof 

Support

Bracket

4x16 Round 

Head Screw

Front Roof 

Support

1

2

3

Summary of Contents for Realtree



































Reviews:

No comments

Brands by name

Popular brands

Load more brands