Our obligation is contingent upon proper use of “Autobrade Red” tools in accordance with factory recommendations, instructions and practices.
The warranty shall not apply in these cases:
1. Normally wearable parts such as bearings, rotor blades, etc.
5. Tools requiring normal tune-up or cleaning.
2. Consumables such as erasing pads, etc.
6. Tools being used after they are badly worn such as using ratchet with worn yoke.
3. Misuse, neglect in maintaining tool or tool modification.
7. Ratchets, anvils damaged by excessive hand torquing.
4. Lack of lubrication or evidence of rust, dirt or corrosion.
8. Use in production-type applications.
Maintenance Instructions
Important:
To keep tool safe a Preventative Maintenance Program is recommended whenever portable power tools are used.
•
Use only genuine Dynabrade replacement parts to insure quality. To order replacement parts, specify
Model#
,
Serial#
and
SPM
of your air tool.
•
It is strongly recommended that all Dynabrade air tools be used with a Filter-Regulator-Lubricator to minimize the possibility of misuse due to unclean
air, wet air or insufficient lubrication. Dynabrade recommends the following:
10681
Air Filter-Regulator-Lubricator (FRL) – Provides accurate air pressure
regulation and two stage filtration of water contaminates.
•
Dynabrade recommends one drop of air lube per minute for each 20 SCFM (example: if the tool specification states 40 SCFM, set the drip rate on the
filter-lubricator to 2 drops per minute). Dynabrade Air Lube (P/N
95842
: 1 pt 473 ml) is recommended.
Routine Preventative Maintenance:
Check free speed of RedTred
TM
Eraser Disc Tool regularly using a tachometer without an accessory attached. Test with
90 PSIG at the inlet while tool is running. Always check tool speed after any maintenance or repair. If tool is operating at a higher RPM (speed) than marked
on the housing, or operating improperly, the tool must be corrected before use.
•
Lubricate the bevel gears through the grease fitting located in the
18747
Angle Head Assembly.
Apply 2-3 plunges for every 40 hours of use
, to
achieve maximum gear life. (Order
95542
Grease and
95541
Gun)
•
Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters, ketones,
chlorinated hydrocarbons or nitro carbons.
•
DO NOT clean or maintain tools with chemicals that have a low flash point (example: WD-40
®
).
•
Air tool stampings must be kept legible at all times, if not, reorder and replace. User is responsible for maintaining specification information.
i.e.: Model #, S/N, and SPM.
•
Blow air supply hose out prior to initial use.
•
Visually inspect air hoses and fittings for frays, visible damage and signs of deterioration. Replace damaged or worn components.
•
Refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No.
95903
) for safety information.
After maintenance is performed on tool, add a few drops of Dynabrade Air Lube (P/N
95842
) to the air line and start the tool a few times to lubricate air motor.
Check for excessive tool vibration.
Handling and Storage:
•
Use of tool rests, hangers and/or balancers is recommended.
•
Protect tool inlet from debris.
•
DO NOT carry tool by air hose or throttle lever.
•
Protect accessories from exposure to water, high humidity, freezing temperature and extreme temperature changes.
•
Store accessories in protective racks or compartments to prevent damage.
•
DO NOT rest tool on eraser disc or eraser hub.
Autobrade Red Tool Warranty
Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within
6 months
from the of date purchase, “Autobrade Red” tools are warranted against defects in workmanship and materials under normal use and service.
We shall, at our option, repair or replace at our factory, any “Autobrade Red” tool which shall, within 6 months
after delivery to the original purchaser, indicate upon our examination to have been defective.
