background image

3

SAFETY INFORMATION 

 

• Use caution when assembling and operating this unit to avoid cuts and scrapes from edges.

• DO NOT use this product in a manner other than its intended purpose. It is NOT intended for

  commercial use. It is NOT intended to be installed or used in or on a recreational vehicle

  and/or boats.

• DO NOT store this unit near gasoline or other combustible liquids or where other combustible 

  vapors may be present.

• DO NOT use, store or operate this unit in an area accessible to children or pets. Store this unit in a 

  dry protected location.

• DO NOT leave the unit unattended while in use.

• DO NOT leave hot ashes unattended, until the unit cools completely.

• DO NOT move the unit while in use, or while ashes are still hot. Allow the unit to cool completely

  before moving or storing.

• NEVER use gasoline, kerosene, Zippo/Ronson lighter fluid, or other highly volatile fluids as a starter.

• Always cook your food on the grate after the flame is burned out.

• Dispose of cold ashes by wrapping them in heavy-duty aluminum foil and placing in a

  noncombustible container. Make sure that there are no other combustible materials in or near

  the container.

• If you must dispose of ashes in less time than it takes for the ashes to completely cool down, 

  remove the ashes from the unit using heat-resistant gloves along with long metal tongs or 

  fireplace shovel. Place the coals in aluminum foil and soak them completely with water before 

  disposing of them in a noncombustible container.

• Allow the unit to cool completely before conducting any routine cleaning or maintenance.

• This product will be hot during and after use. Use insulated oven mitts, or gloves, for protection 

  from hot surfaces or splatter from cooking liquids.

• Grease or other liquids inside the grease cup will be hot after using this appliance.  Allow the 

  grease cup to completely cool before removing or disposing. If the grease cup must be removed 

  before it's allowed to completely cool, use heat resistant gloves or mitts for removal or disposal.

• Use caution when opening the lid of the unit while in operation. Keep hands, face and body safe 

  from hot steam or flare-ups. DO NOT inhale smoke.

• DO NOT wear loose clothing while operating the unit. Tie back long hair while operating the unit.

• ALWAYS wear shoes that fully cover your feet while operating the unit.

• NEVER use glassware, plastic or ceramic cookware on or in the unit. Use metallic cookware only.

• Use of accessories not intended for this unit is not recommended and may lead to injury or

  property damage.

WARNING

This product and the fuels used to operate this product (charcoal or wood), and the

products of combustion of such fuels, can expose you to chemicals including carbon black, 

which is known to the State of California to cause cancer, and carbon monoxide, which is 

known to the State of California to cause birth defects or other reproductive harm. 

For more information go to www.p65Warnings.ca.gov

CALIFORNIA PROPOSITION 65

Summary of Contents for Signature DGSS443CB
















Reviews: