background image

9

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

NOTICE : The major electrical components of this heater are protected by a safety fuse mounted to the PCB board.

If your heater fails to start, check this fuse first and replace as necessary.       You should also check your

power source to insure that proper voltage and frequency are being supplied to the heater.

TO STOP HEATER

1. Turn switch to “OFF” and unplug power cord.

TO RESTART HEATER

1.Wait 10 seconds after stopping heater.

2. Repeat steps under to start heater.

EXTRA ELECTRIC OUTLET & PIGGYBACK POWER CORD

WARNING : SHOCK HAZARD!

8. LONG TERM STORAGE OF YOUR HEATER

FUEL TANK DRAIN

1. Drain fuel tank through fuel cap opening. 

(For RMC-KFA50DGD/75TDGD Models Only)

2. Remove fuel drain bolt from rear bottom side of fuel tank using 3/4” socket or adjustable wrench and drain.

(For RMC-KFA125/170/210TDGD-01 Models Only. See Figure 10)

3. Using a small amount of kerosene, swirl and rinse the inside of the tank.

NEVER

 mix water with the kerosene as it will cause rust inside the tank.

Pour the kerosene out making sure that you remove it all.

IMPORTANT :

Do not store kerosene over summer months for use during next heating season.

Using old fuel could damage heater.

4. Reinstall fuel cap. Properly dispose of old and dirty fuel. (For RMC-KFA50DGD/75TDGD Models Only)

5. Reinstall fuel drain bolt to Fuel tank and tighten firmly using 3/4” socket or adjustable wrench. 

    (For RMC-KFA125/170/210TDGD-01 Models Only. See Figure 10)

   

IMPORTANT : 

Before reinstalling the fuel drain bolt, make sure the seal is on the bolt. If the seal is

                               not used the bolt cannot be installed correctly and the fuel tank will leak.

6. Store heater in dry well ventilated area.  Make sure storage place is free of dust and corrosive fumes.

7. Store the heater in the original box with the original packing material and keep the USER’S MANUAL

with the heater.

 Always cover electric outlet 

when not in use.

 Don’t plug and use a appliance

more than 120V/60Hz 5A 

current in this outlet

Figure 10. Fuel Drain Bolt

Fuel Drain Bolt

Seal

r

e

v

o

C

r

e

v

o

C

Outlet

RMC-KFA210TDGD-01 Model Only     RMC-KFA75TDGD/125/170TDGD-01 Models only

Figure 9. Electric Outlet

Outlet

Summary of Contents for RMC-KFA125TDGD-01































Reviews: