background image

U S E R   G U I D E

 

|

 

U V C S   S I D E CU R E   C O N V E Y O R

 

5

                 

 

Specific Safety Considerations 

Dymax light-curing conveyors are designed to maximize operator safety and minimize exposure to UV light. To use the 
conveyor safely, it must be set up and operated in accordance with the instructions in this user guide.  

Equipment is designed to be used when properly set up, with components correctly connected, and operated in accordance 
with 

relevant

 instructions. 

Design was developed to maximize operator safety and minimize exposure to UV. 

CAUTION!

  Always wear UV eye protection or face shield, when working near UV light! 

Safety Recommendations 

 

Use eye protection or a face shield approved for complete UV protection. 

 

Long-sleeved shirts or a lab coat are recommended to protect the arms, and the use of UV opaque gloves to protect 
the hands.

 

 

Dymax UV Light-Curing System Safety Considerations 

Dymax UV light-curing technology has been used successfully for over 30 years.  The fast cure, one-component nature of our 
UV light-curing technology has made it the process of choice for many manufacturers requiring a "cure on demand" assembly 
process. Operators must understand these four concepts to use the UV light source safely: UV exposure, high-temperature 
surfaces, ozone, and bright, visible light.  

UV Exposure 

Standard Dymax UV light-curing systems have been designed primarily to emit UVA energy (Figure 1). UVA energy is 
generally considered the safest of the three UV ranges: UVA, UVB, and UVC. Although OSHA does not currently regulate UV 
light exposure in the workplace, the American Conference of Governmental Industrial Hygienists (ACGIH) does recommend 
Threshold Limit Values (TLVs) for ultraviolet light. 

The strictest interpretation of the TLV (over the UVA 

range) for workers’ eyes and skin allows continuous exposure up to 1 

mW/cm

2

 (intensity). Unless you are placing bare hands into the curing area, it is unusual to exceed these limits. To put 1 

mW/cm

2

  limit into perspective, a cloudless summer day will typically exceed 3 mW/cm

2

 of UVA light, and also include the more 

dangerous UVB light (primarily responsible for sun tans, sun burns, and skin cancer) as well.  

Figure 1.  
UV Spectrum  

 

Summary of Contents for SideCure UVCS





















Reviews: