background image

 

 

Dymax BlueWave® LED Prime UVA User Guide 

Safety 

Before continuing with the installation, please read the following chapters of this manual for safety 
recommendations and installation, operation, and troubleshooting instructions. 

CAUTION!

  Always wear protective goggles or face shield when working near the front of the 

unit, which emits high-intensity visible light!   

WARNING!

  Always observe safety requirements! 

CAUTION!

  Risk of electrical shock if cover is removed! 

To use this system safely, it must be set up and operated in accordance with the instructions given by Dymax.  

The system’s design was developed to maximize operator safety and minimize exposure to UV. Using the 

system in any other manner will impair the protection of the system.  Dymax assumes no liability for any 
changes that may impair the protection of the system. 

Safety Recommendations 

■ 

Use the goggles provided or an approved face shield for eye/face protection. 

■ 

Long-sleeved shirts or a lab coat are recommended for arm protection. The use of UV opaque gloves will protect 
the hands. 

NOTE: The BlueWave LED Prime UVA emits high-intensity light.  Never look directly at the light-emitting end of 
the lightguide while the unit power is on. 

Safety Symbol Index 

The following symbols are displayed on the curing system. Please see below for their meanings. 

 

Refer to  Manual 

 

Warning! 

 

Eye Protection Required 

 

Warning! UV Light Hazard 

Sécurité  

 

PRÉ-CAUTION!

 

Toujours faisez de l’usage des lunettes de protection ou protéger de visage 

marc

he près du devant d’élément!

 

AVERTISSEMENT!

 Remmarquez toujours besoin de sécurité! 

PRÉ-CAUTION!

 Risque de décharge électrique quand le couvert est enlever! 

Summary of Contents for BlueWave LED Prime UVA DX-1000

























Reviews: