31
DXE-STPL-100BD - Radial Wire Staple, Biodegradable, 3", 100 pack
DX Engineering
DXE-STPL-100BD
is a 100-pack of 3”
biodegradable
anchors that are produced from recycled PLA
(Polylactide Resin). Depending on the weather conditions, they will degrade in about a year. They are easily installed and
will hold radial wires in place until lawn roots overtake them - and then disappear. Ecologically friendly!
DXE-STPL-100P - Radial Wire Metal Anchor Pins, 100/pack
DXE-STPL-300P - Radial Wire Metal Anchor Pins, 300/pack
DX Engineering Radial Steel Wire Anchor Pins are perfect for fastening radials below the grass line to eliminate the
risk of damaging your radials during lawn maintenance.
100 & 300 count - 6'' Pins
11-Gauge
DXE-225RT-20 - Ring terminal 16-14 Wire Gauge, 1/4" hole/20-pk
This is a set of 20 ring terminals for AWG #14 to 16 wire with a clearance hole for a 1/4" bolt. These are the same crimp
terminals supplied with the DXE Radial Wire Kits for #14 Radial and Antenna Wire.
SUM-900031 - Automatic Wire Stripper/Crimper/Cutter, 24-10 Ga.
Our DX Engineering wire stripper uses a spring-loaded design to make quick work of wires ranging from 24 to 10 gauge. Just insert
the wire, squeeze the handle, and listen for the click. That’s the sound of another perfect wire stripping job performed in about 2
seconds- a fraction of the time it takes your pocket knife to do the same job. An adjustable wire length guide helps you
make uniform strips, and a built-in wire cutter and crimper helps you complete your wiring job.
Spring-loaded design
Strips wires ranging from 24 to 10 gauge
built-in wire cutter and crimper
DXE-CS2-100 - Copper Strap Roll, 2 in. x 100 ft.
Use ground strap to tie equipment back to a common ground point. Copper strap should also be used to make a non-
resonant counterpoise for towers mounted on mountaintops or other rocky terrain.
Copper strap has lower inductance than wire so it is a better choice for providing ground paths
.
DXE-GUY1000-KIT - Guying Kit for DX Engineering Vertical Antennas and Masts
This kit is intended for taller, multi-point guyed antennas and masts. Some vertical manufactures indicate their antennas do not need
guying. During times of high winds or ice loading however, some of these verticals may sustain damage or fail altogether. With the
small amount of effort needed to install a four point guying system, the risk hardly seems worth taking. A four-point guying scheme
provides the best mechanical advantage to prevent wind stress, regardless of direction. The guying is
intended for stability, and should never be depended on for primary support.
A four point guying system is recommended for use with a DX Engineering Tilt-Base, because just one of
the guy ropes has to be loosened when you tilt the vertical down. The remaining guys help stabilize the
vertical in three directions when being raised.
These Vertical Guying kits have been designed to be used with ground mounted 1/4 wavelength vertical
antennas such as DX Engineering monoband and multi-band verticals. The kits can also be used for other
ground mounted verticals exceeding 30 feet high with four point guying at two or three levels on the vertical radiator. The guying kits
are ideal for fixed or portable installations.
The
DXE-GUY1000-KIT
is designed for taller verticals by providing sufficient rope for three-level guying.
Included in this kit is:
(4) Heavy Duty
DXE-EA15
15 in x 3 in. screw-in earth anchors with eyelets
(1) 1000 ft Roll of UV resistant, 3/32 Double-Braided Dacron Polyester Rope (part number
SYN-DBR-94-1000
)
