background image

AZDEN 

8-Pin Round Mic Connector - 

TGR-SL-CAB8R

 

Radio Models

 

Pin-out 

Notes 

JP-1 

PCS-5000 
PCS-6000 
PCS-7000 

Pin 1 - Mic Input 
Pin 2 - GND 
Pin 3 - N/C 
Pin 4 - N/C 
Pin 5 - N/C 
Pin 6 - N/C

 

Pin 7 - PTT 
Pin 8 - N/C 
 
 

Speaker audio is available on some models.  Check your 
radio manual for availability of these signals and add the 
appropriate jumpers.

 

 

 
 
 

DRAKE 

4-Pin Round Mic Connector - 

TGR-SL-CAB4R

 

Radio Models

 

Pin-out 

Notes 

JP-1 

TR-7 
TR-22 
TR-33 
UV-3

 

 

Pin 1 – Mic Input  
Pin 2 – PTT 
Pin 3 – N/C  
Pin 4 – GND 
 
 
 
 
 
 

 

 

 
 

ELECRAFT 

8-Pin Round Mic Connector - 

TGR-SL-CAB8R

 

Radio Models

 

Pin-out 

Notes 

JP-1 

K2 
K3 

Pin 1 - Mic  
Pin 2 - PTT 
Pin 3 - NC  
Pin 4 - NC 
Pin 5 - NC 
Pin 6 - +5VDC 
Pin 7 - GND 
Pin 8 - GND  
 
 

The Mic jack on the K2 can be wired a number of 
different ways, so before installing the jumper wires, 
you MUST verify that the pin-out of your K2 matches 
that shown here.  

 

 
 

ELECRAFT 

Rear Panel Audio In, Audio Out and PTT connectors  - 

TGR-SL-CABK3

 

Radio Models

 

Pin-out 

Notes 

JP-1 

K3 only 
 
 
 
 
 
 
 
Check the SLMODK3 
    Jumper Module list 

Pin 1 - SPKR  
Pin 2 - GND 
Pin 3 - MIC  
Pin 4 - PTT 
Pin 5 - GND 
Pin 6 - GND 
Pin 7 - N/C 
Pin 8 - N/C 
 

Some customers have found that the K3's "Line In" gain 
(menu setting) is set to zero by default, thereby resulting 
in no power output when transmitting. If up experience 
this problem, then please consult your radio manual for 
instructions on turning up this control.  
 
Note that the K3 also has a menu setting for the "Line 
Out" level, which can be turned up if needed to increase 
the RX Audio going into the SignaLink 
 

 

 

Summary of Contents for Tigertronics SignaLink TGR-SL-USB


















Reviews:

Related manuals for Tigertronics SignaLink TGR-SL-USB