DX Engineering DXE-TW Series Instructions Manual Download Page 2

- 1  - 

Introduction 

 
The DX Engineering TW Antenna systems are designed with 6063 corrosion-resistant aluminum 
tubing, tough fiberglass, easy to use assembly parts and stainless steel hardware. These antennas are 
very durable and attractive with their black powder coating for added stealth in an HOA or portable 
environment. 

 

The TW antenna is an omni-directional center fed vertical dipole with a very low radiation take-off 
angle (approximately 27 degrees above the horizon), allowing for very long skip using low power 
on 20, 17, 15, 12 and 10 meters. 

 

Systems include Remote or Manual switching Multi-Band operations covering 20, 17, 15, 12, and 
10 meters or Mono-Band systems for 80, 60, 40 or 30 meters. You can also use one of the multi-
band systems and enhance your operating capabilities by adding the mono-band components. 

 

There are multiple packaged combinations as well as individual parts, available for customizing the 
best system for your specific requirements.  

 

The TW antenna system is only 8-1/4 feet tall and 5 feet wide and can be set up easily in practically 
any location by one person. No more trying to string up wires or getting tangled up in trees for 
portable operations. You supply the coax and your own powered transceiver. It's perfect for portable 
operations, anywhere and anytime. 

 

For backpacking and general camping and travel a custom travel/storage bag holds all of the 
antenna components for easy transportation or storage is also available. 

 

For portable use, the lightweight Quadrastand lets you set up your DX Engineering HF Portable TW 
Antenna wherever you happen to be. Think about special operating events like the Scouts Jamboree 
On-The-Air (JOTA), Field Day, SOTA (Summits On-The-Air), Ohio State Parks On The Air 
(OSPOTA) and more. 

 

One person can easily and quickly set up the antenna system allowing you to devote your time to 
being on the air and having fun making contacts. 
 

Features 

 

Two Multi-Band models and 4 Mono-Band models 

 

Tough 6063 corrosion-resistant aluminum antenna components 

 

Black powder coat finish for stealthy operation (Quadrastand has gray legs) 

 

Power Handling: 1200 W SSB, 800 W CW, 500 W RTTY, 375 W AM 

 

Band Width 200 kHz 20 m, Entire Band on 17, 15 and 12m, 1210 kHz on 10 m* 

 

Typical Minimum SWR 1.1:1 on 20, 17, 15, 12 and 10 m* 

 

Mono-Band versions available for 80, 60, 30 and 40 meters 

 

Antenna is only 8-1/4 feet tall by 5 feet wide 

 

Permanent Ground Mount  or Portable Quadrastand 

 

Light, easy to transport - approximately 10 pounds 
 

* Test conditions: 100 feet of RG8/U coax, 100 W output power, antenna mounted approximately 24” above  
   ground with no external objects, metallic or otherwise, within 25 foot radius of the antenna. 

 

 

Summary of Contents for DXE-TW Series













Reviews: