manualshive.com logo in svg

DX Engineering DXE-RFS-SYS-3P, Manual

Share
Download
DX Engineering DXE-RFS-SYS-3P Manual Download Page 22

22 

DXE-SNS-CT1 - Compression Tool for Snap-N-Seal 75 Ω Coaxial Connectors 

 

Ratchet compression tool for installing 

Snap-N-Seal

 75 Ω Coaxial connectors. Ordinary pliers will not install 

these connectors properly.  
 
 
 

COM-CW4  -  Cable, 4 Conductor, Sold per Foot 

 

A high quality, PVC jacketed 4-wire control cable, COM-CW4 consists of 4 #20 AWG conductors. It may be 
used in a multitude of control cable applications, such as remote switching and antenna rotators. 
  
Sold by the foot - order the length you need. 

 
 
 
SUM-900031 - Automatic Wire Stripper/Crimper/Cutter, 24-10 Ga.

 

Our DX Engineering wire stripper uses a spring-loaded design to make quick work of wires ranging from 24 to 10 gauge. Just insert 
the wire, squeeze the handle, and listen for the click. That’s the sound of another perfect wire stripping job performed in about 2 
seconds- a fraction of the time it takes your pocket knife to do the same job. An adjustable wire length guide helps 
you make uniform strips, and a built-in wire cutter and crimper helps you complete your wiring job.  

 

Spring-loaded design  

 

Strips wires ranging from 24 to 10 gauge  

 

built-in wire cutter and crimper 

 

 
 

 

KLE-11055 - Klein-Kurve Wire Stripper / Cutter 11055, 18-22 AWG

 

Klein Tools Klein-Kurve wire strippers are ideal for stripping solid (10-18 AWG) and stranded  (12-20 AWG) wire 
cleanly and easily. The 7 1/8 in. strippers also have precise shear-type blades to cut copper wire nicely, easy-to-read 
markings on both sides, and extra-soft grips and curved handles for comfort.  

 
 
DXE-CIT-1  -  F Connector Tightening Tool 

The CIT-1 installs and removes F connectors in high density and hard to reach locations, and is the only tool that works 
with bent coax.  Only finger force is required. Provides enough leverage to achieve a 30 in/lb tightening force by hand. 
Helps insure proper connections thereby reducing the potential of loose connector related service calls. 

 

 
 

 

JTL-12555  - Jet-Lube

™

 SS-30 Pure Copper Anti-Seize  

Jet-Lube

™

 SS-30 Pure Copper Anti-Seize is the top choice of engineers and technicians in government, industry and leading Amateur 

Radio contest stations, for protecting mechanical assemblies of aluminum tubing, general hardware and copper grounding 
systems. On bonded metal surfaces Jet-Lube

™

 SS-30 assures electrical and RF conductivity while preventing oxidation 

and corrosion. Surpassing the capabilities of other aluminum anti-oxidants, the wide temperature range of Jet-Lube

™

 SS-

30 prevents long-term drying and caking, and allows easy disassembly and effortless cleaning of parts. An 
environmentally preferred thread lubricant and conductive termination compound, Jet-Lube

™

 SS-30 helps keep your 

equipment in serviceable condition. It contains a high concentration of copper flakes, a requirement for heavy loads or 
compression; controlled frictional characteristics allow the surfaces of nuts and bolts to be tightened to their design torque 
specifications. This anti-seize product assures full hydraulic efficiency by allowing the metal surfaces to slide over each 
other without damaging metal-to-metal contact. Jet-Lube

™

 SS-30 is also designed to work as a similar and dissimilar 

component between two metal surfaces to prevent seizing and galvanic action. The SS-30 compound formula improves 
conductivity and ground continuity - and will not melt in high temperatures.  
  Jet-Lube

™

 SS-30 Pure Copper Anti-Seize Features include: 

* Meets MIL-PRF-907E spec 
* K-factor: 0.13 
* Service rating: -65 degrees F (-54 degrees C) to 1800 degrees F (820 degrees C) 
* SS-30 Resistivity (ohm-CM x 108) 5 

 

Summary of Contents for DXE-RFS-SYS-3P

























Reviews:

No comments

Brands by name

Popular brands

Load more brands