background image

- 2 - 

The DX Engineering 

DXE-8040-30AOK

 kit adds 30 meter coverage to the DX Engineering 80/40 

dual band vertical antenna without giving up any existing band coverage.  
 
This kit will operate across the entire 30 meter band at full legal limit with an SWR of 1.5:1 or less 
and adds negligible wind loading to the antenna. 
 
No disassembly of the existing antenna is required. 
 
Simply install this kit, check the tuning (if needed, make some minimal tuning adjustments) and 
you're on the air with an additional band.  

 
 

Included Materials 

 

 

Pre-assembled 14 ga stranded, tin coated, FLEX-WEAVE™ 30 Meter element wire with 

soldered ring terminals 

 

Six Stainless Steel Band Clamps with Threaded Studs 

 

Lower, Middle and Upper Laser Cut Stainless Steel Mounting Arms 

 

Two 12 inch Hot Roz™ with Black Vinyl Covers for one end 

 

Patented Serpentine Insulators (US Patent No. D534,905) 

 

All Stainless Steel Hardware 

 

 

Parts List

 

Quantity 

Description 

Stainless Steel Laser Cut 30 Meter AOK Mounting Arm 

30 Meter AOK Hot Rodz Bracket. 

30 Meter AOK Insulated Bracket # 1 

31 Meter AOK Insulated Bracket # 2 

End Insulator - Polyamide Wire/rope connection (US Patent No. D534,905) 

Flex-Weave™ 30 Meter Wire Assembly, 233.00" with Soldered Ring Terminals 

Wire Assembly, 23.50" Black PVC Insulated with #10 and 1/4" Soldered Ring Terminals 

Stainless Steel Hot Rodz™, 12" 

3.00" Studded Element Clamp w/ Stainless Steel Hardware 

2.500" Studded Element Clamp w/ Stainless Steel Hardware 

2.25" Studded Element Clamp w/ Stainless Steel Hardware 

Stainless Steel Spring, 1.75" 

Black Plastic End Cap for Hot Rodz™ 

10 

# 10-24 x 3/4" Stainless Steel Carriage Bolt 

# 10-24 x 1" Stainless Steel Carriage Bolt 

# 10-24 x 5/8" Stainless Steel Hex Bolt 

15 

# 10 Stainless Steel Flat Washer 

# 10 x 1" x 0.62" thick Stainless Steel Fender washer 

15 

# 10 Stainless Steel Split Washer 

# 10 Stainless Steel External Star Washer 

14 

# 10-24 Stainless Steel Hex Nut 

# 10-24 Stainless Steel Nyloc Hex Nut 

# 10-24 Stainless Steel Wing Nut 

Summary of Contents for DXE-8040-30AOK

















Reviews: