background image

6

5.  Basic setting of the Mini-stop

5.1 Generally

The Mini-stop DC 1550/DA320 does not necessarily need the control panel V810/VV820 when running. All parameters can be set

using push the buttons and the display on electronics box, the panel V810/V820 will however enable the operator to work more

easily with regard to its position. The description of the push-button panel and that of the panels V810/V820 is given in the

instruction manual, part A, par. 7. The general procedure of setting parameters with the panel V8120/V820 is given in the

assembling instructions with standard drives, part. B1, par. 5.1 and appllies also to DC 1550/DA320.

5.2 Setting of Mini-stop EFKA DC 1550/DA320

Elements  of the electronics box

Front side

S1

Button P

calling or leaving the programming mode

S2

Button E

option of initial bartack (switched off, simple, double) within the programming mode of the confirmation

of changes

S3

option of final bartack (switched off, simple, double) within theprogramming mode of enhancing

the displayed value

S4

Button -

position of the presser foot when stopping in the seam (down, up)

position of the presser foot after trimming (down, up) within the programmed mode of reduction of

the displayed value

S5

Button 

»

position of the needle when stopping in the seam (down, up) within the programming mode  of shifting to

the next digit

LED1

indication for the start single bar

LED2

indication for the start double bar

LED3

indication for the end single bar

LED4

indication for the end double bar

LED5

ndication for automatic presser foot lifting when stopping in the seam

LED6

indication for automatic presser foot lifting after having ended the seam (trimming)

LED7

indication for stopping in the seam with the needle in its bottom position

LED8

indication for stopping in the seam with the needle in its top position

Display

3 digits

Reae side

B2

connection of the commutating  motor scanner

B18

connection of the  light barrier module (photocell)

B41

connection of the  motor stator winding

B80

connection of the pedal set value initiator

B776

connection of the panel V810/V820

A (ST2)

connection of electric elements of the sewing machine (electromagnets, electropneumatic valves,

push-buttons …)

Summary of Contents for 4182i-1












Reviews: