DURAVIT Pool Operating Instructions Manual Download Page 45

Page: 45 / 52

Problem

Potential cause

Solution

See
page

“Hygiene” button flashes.

Hygiene and tempera-

ture circuit stopped manu-

ally.

Press the “Hygiene” button.

The “Hygiene” button lights

up, the hygiene and tem-

perature circuit starts.

“Water level too low” is

also displayed.

Refill the water until the

water level is about 50

mm above the uppermost jet.

A continuous acoustic

signal sounds.

Heating defective.

Please call Customer Ser-

vice.

Foaming

Soap, shampoo, wrong /

too much cleaning / care

agent in bathwater

Empty pool, clean and refill. 43

Whirl system does not

start.

Mains switch switched off.

Switch on at mains.

Earth leakage current

protection tripped.

Check whether the earth

leakage current protection

has tripped.

Otherwise:

Please call Customer Ser-

vice.

Water flows out of the vent

valve, while a whirlpool

system is active.

This is normal because the

air valve is vented while

some water escapes.

Water runs out continu-

ously from the vent valve.

Filter fouled

Replace the filter.

Air valve is wrongly in-

stalled

Remove the valve and re-

install as described.

Air valve fouled

Clean the air valves under

running water.

Air valve defective

Replace the air valves and

filter.

Remote control does not

respond.

Battery drained.

Recharge the remote con-

trol for at least 3 hours.

Remote control has

dropped into energy saver

mode.

After having been stored

outside of radio range, the

remote control needs to be

reactivated:

Place the remote control on

the charging station.

After 2 seconds, the “Emo-

tion” button lights up.

Summary of Contents for Pool





















































Search results

Summary of Contents for Pool

Reviews:

Related manuals for Pool

Brands by name

Popular brands

DURAVIT Pool, Operating Instructions Manual

Search results

Summary of Contents for Pool

Reviews:

Related manuals for Pool

Brands by name

Popular brands