background image

8

 

MK4A LOUVRE WINDOW (Optional)

 

Step 2:

 

On  the  inside  of  the  shed,  position  studs 
and  Nog  centrally  on  window  opening. 
Make  sure  the  studs  are  parallel  and  nail 
into Top Plate and end wall Nog.

 

Step 3:

 

Nail  wall  Sheets  to  window  framing  using 
30mm  clouts.  (return  to  step  4  on  page  7 
and  complete).  Then  fit  Window  Frame). 
Position  Window  Frame  centrally  on  win-
dow  opening  and  rivet  it  to  ribs.  Pre

-

drill 

holes  in  each  corner  and  nail  Window 
Frame to framing, using 50mm nails.

 

Step 4:

 

If  the  Window  is  in  the  gable  end,  tempo-
rarily  position  the  Over  Panel  above  Win-
dow  Frame.  Following  the  same  angle  as 
the gable, mark and cut to suit.

 

Step 5:

 

Rivet  Over  Panel  to  the  Window  Frame 
with rivets.

 

588mm

 

Step 1:

 

Lay out the two window studs (883mm) and 
Nog  (634mm)  on  a  flat  surface.  Position 
Nog and nail in place using 2x 75mm nails 
at each end.

 

Step 6:

 

From  the  inside  of  the  shed,  slide  Louvre 
Glass  into  Louvre  Units  attached  to  the 
Window  Frame.  Bend  up  tabs  to  keep 
Glass in position.

 

50mm

 

NAILS

 

RIVITS

 

Summary of Contents for SHEDS MK4A

















Reviews:

Related manuals for SHEDS MK4A