29
H - 8 0 0 T U B G R I N D E R
O P E R A T I N G I N S T R U C T I O N S
2.5 Storage
2.5.1
Preparing for storage
To prepare the unit for storage, perform the following steps:
1. Check the wheel bearings for lubrication requirements and adjustments at the end of the season.
2. Check the pressure roller bearings for lubrication and adjustments at the end of the season.
3. Clean the machine thoroughly to prevent rust and to make inspections easier. Clean and repaint the tub
floor to prevent rust and sticking problems at start up time.
4. Check for loose or worn chains, belts, sprockets, and pulleys.
5. Check the condition of bearings.
2.5.2
Removing from storage
To prepare the unit for use after storage, perform the following steps:
1. Perform a thorough pre-operation inspection.
2.6 Installing or changing a screen
CAUTION:
Follow normal shutdown procedures and make sure rotor and all moving parts come to
a complete stop before installing or changing the screen.
Using a screen with smaller holes will produce a finer cut. Where a coarse cut is desired, use a screen with a larger hole.
Screens can be reversed when one edge becomes worn.
To change screens, perform the following steps:
1. Remove the auger/screen access door on
the right side of the machine.
2. Remove six bolts, washers and nuts from
the screen currently installed.
3. Slide screen out.
4. Insert new screen
5. Replace bolts, washers, nuts and access
door.
6. Replace the auger/screen access door.
screen
screen access door
Summary of Contents for HAYBUSTER H-800
