Durafly ME-163 V2 Instruction Manual Download Page 2

A  WARNING: 

Read this instruction manual fully so as to become completely familiar with the features of 

this product before operating.  Failure to operate this product correctly could result in 

damage to the product, personal property and cause serious injury. This is a sophisticated 

hobby product and is NOT a toy. It must always be operated with caution, common sense 

and some basic mechanical ability. This manual provides instructions as to the assembly, 

safe operation and maintenance of this hobby product. It is highly recommended that you 

follow and read fully the instructions and warnings stated in this manual including safety, 

assembly, set-up and flying guidelines in order to operate this product correctly and avoid 

damage or serious injury. 

SAFETY PRECAUTIONS: 

As the user of this product you and you alone are responsible for operating it in a manner 

that does not endanger yourself and others around you or result in damage to the product or 

property of others. This product is operated via a radio controlled system that in some cases 

can be subject to interference from sources outside of your control. Interference may result 

in a momentary loss of control so it is always recommended that this product be used in a 

suitably open outdoors space. 

- This is a radio controlled flying model and as such must always be flown with caution and 

care. This is not a toy.

- This model is designed for intermediate to advanced pilots.

- Alway exercise great caution when using the recommended battery to power this product. 

For full safety notes and operating procedures, please see information provided by your 

battery supplier.

- Take great care when connecting/disconnecting the battery. See battery supplier for full 

safty procedures.

- Never power up the model in confined spaces and always keep the prop clear of 

obstructions.

- This product is not a toy. Children must be accompanied by an adult at all times if operating 

this product.

- Only fly this model in an open area away from crowds, people, buildings, trees, power lines 

and obstructions.

- Always put safety first when operating this model and consider the warnings stated above.

- The supplier/manufacturer accepts no responsibility for damage or injury caused through 

the use of the product.  Not suitable for children under the age of 14. THIS IS NOT A TOY.

Summary of Contents for ME-163 V2



























Reviews: