background image

 

 

Diagram 2:  Typical panel arrangments (Style CG-4T panels shown - 2T similar) 

 

CONSTRUCTION 

 

Delivery 

The purchaser is responsible for off-loading, and must 

examine the radiant panels promptly upon receipt. 

Any claims for damage will only be accepted if, at the 

time of delivery, the consignment note is endorsed 

with the details and counter signed by the transport 

driver. 

 

Handling 

Radiant panels are usually palletised so a fork-lift or 

similar will be required for lifting. Individual panels can 

usually be handled by one or two persons. Panels 

must not be dropped or suffer impact in any 

circumstances.

  

 

Storage 

Radiant panels should be stored in clean, dry indoor 

conditions. Packaging should not be removed until the 

panel is required for installation (the radiant surface of 

each panel is covered in a protective film which should 

be removed when installation and commissioning is 

complete). Any packaging should only be removed if 

damage is suspected at the time of delivery. 

Preparation 

Evo-Lite Style CG radiant panels are intended for 

horizontal installation within a standard 600mm ceiling 

grid ; 

hence it is important to liase with other trades to 

co-ordinate installation. Provision must be made for 

proper fixings ; the ceiling, soffit or structure must be 

suitable to accept proposed fixings such as expanding 

anchors, drop rods, lindaptors etc. Refer to Table 1 for 

panel masses. 

 

Access is recommended for maintenance i.e. pipe 

connections. Ceiling tiles, builders work etc should be 

removable with sufficient clearance. Evo-Lite should 

be free to expand during normal operation.  

 

Warning 

Some components may have sharp edges. Care must 

be taken when handling the product and protective 

gloves should be worn. 

 

 

 

 

 

 

Nominal panel length (mm) 

600  900  1000  1200  1500  1800  2000  2100  2400  2500  2700  3000 

Mass of panel 2T (kg) 

3.1  4.7  5.2  6.2  7.8  9.4  10.4  10.9  12.5  13.0  14.0  15.6 

Mass of panel 4T (kg) 

4.3  6.4  7.1  8.5  10.7  12.8  14.2  14.9  17.1  17.8  19.2  21.3 

Table 1 : 

Masses of Evo-Lite Style CG radiant panels 

 

 

N.B. Style CG panels have a nominal installed mass of approximately 10kg/m² 

 

 

Page 2 of 8 

Summary of Contents for Evo-Lite Style CG









Reviews: