background image

 

Precautions 

 

SPRAY CANS MUST BE INSTALLED AS LAST, JUST BEFORE THE COVER CLOSING AND AFTER REALIZING ALL 
THE REQUIRED CONNECTIONS, PROVIDED POWER AND ELECTRICAL SIGNALS FROM CONTROL PANEL AND 
DETECTORS. 
IF NOT PEPEROSSO SHOULD ACCIDENTALLY ACTIVATE THE NEBULISATION. 

 

USING THE DEVICE ACCORDING TO THESE INSTRUCTIONS IS LEGAL. 
IT IS SUGGESTED TO SIGNALIZE ITS PRESENCE WITH SPECIAL SIGNS EASILY VISIBLE TO ALERT THE RISK OF 
IRRITATING SPRAY 

 

ALL THE INSTALLING OPERATIONS MUST BE DONE WITHOUT THE SPRAY CANS INSIDE THE DEVICE! 

 

TO ALLOW THE GAS  IS RELEASED  CORRECTLY  INTO THE ENVIRONMENT AND AVOID  SPOTS,  AVOID THE 
PRESENCE OF ITEMS THAT MEETS THE NOZZLES OF CANS WITHIN 2 METRES. 

 

PEPEROSSO  IS  ACTIVATED  AT  CONTROL  PANEL  ARMING  (COMMAND  CONNECTED  TO  INPUT  IN1):  USE 
ONLY TOTAL ARMING COMMAND. 
DO NOT ACTIVATE PEPEROSSO WHEN IN PARTIAL ARMING BECAUSE IS NOT GUARANTEED THE COMPLETE 
ABSENCE OF PEOPLE IN PROTECTED AREA 

 

DO  NOT  INSTALL  THE  DEVICE  WHEN  IN  PRESENCE  OF  NOT  PACKAGED  FOOD  OR  ENVIRONMENT 
INCOMPATIBLE WITH GAS NEBULISATION. 

 

ATTENTION: PEPEROSSO IS PROTECTED AGAINST WIRE CUTTING: IF PROPER SIGNALS ARE MISSING ON 
MONITORING  INPUTS  (EXAMPLE:  WIRE  CUT,  BLACKOUT  OR  CONTROL  PANEL  BATTERY  TEST  OR  ITS 
FAILURE), GAS NEBULISATION CAN STARTS. 

 

After nebulisation 

The gas nebulized is not harmful to health although it is very irritating. 
The active principle decay after about 36 hours. 
After the area has been saturated with the gas, it is necessary to proceed with an accurate decontamination 
as the residual chilli pepper fine dust may react again after depositing on surfaces. 
Furniture and home furnishings are not damaged. 

 

ensure proper ventilation 

 

irritation subsides in about 30 minutes 

 

contamination of clothes can prolong the action 

 

be careful to not touch your eyes and wash your hands thoroughly 

 

to avoid unpleasant irritation is recommended the use of masks during cleaning 

 

 

Summary of Contents for PEPEROSSO




















Reviews: