background image

 

9

 

D)

 

Alarm Mode 

Scroll down one level and select by pressing the ENT button ALARM OFF, 
CONTINUOUS, TIMED MODE or PULSE MODE. 

1)

 

Alarm OFF 

The alarm facility connected to the PCB relay output will not be active. 

2)

 

Continuous 

The alarm facility connected to the PCB relay output will give a continuous 
alarm/siren output when the alarm is triggered. 

3)

 

Timed mode 

The alarm facility connected to the PCB relay output will give a 3 minute 
alarm/siren output when the alarm is triggered. 

4)

 

Pulse mode 

The alarm facility connected to the PCB relay output will give a 1 second pulse 
alarm/siren output when the alarm is triggered. 

 

On all the above, scroll down to MENU EXIT and press ENT to exit. 
--------------------------------------------------------------------------------------- 

 

From TEST MODE, scroll down to 

PROFILES

 and press ENT. Screen will display:- 

CUSTOMS, HI ACCESS or DOMESTIC & 100-400Kg or 400-700Kg or 700-1000Kg. 

 

1 – Customs,

 press ENT button. 

Scroll and select either, SPEED Mmin, Acc/Dec mm, LOAD=, COLL=, SBEAM and press 
ENT button. 
 
a)

 

SPEED 

 

Press ENT and start to select the following:-

 

 

OPEN=, press ENT and an arrow will appear next to OPEN=.

 

 

Select speed from Min. 8 M/min. to Max. 28 M/min with UP & Down buttons.

 

 

Press ENT button on desired speed.

 

 

Scroll down to CLOSE=, press ENT and select desired speed as above 

 

   (Close Min. speed cannot be greater than Open Min. speed) 

 

Press ENT button on desired speed.

 

 

Scroll down to CREEP=, press ENT button and an arrow will appear next to CREEP=.

 

 

Select creep speed from Min. 1.5M/min to Max. 4M/min.

 

 

 Press ENT button on desired speed.

 

 

Scroll down to CAL and press ENT button, an arrow will appear next to CAL. 

 

Select calibrating speed from Min. 5 M/min to Max. 8M/min. 

 

Press ENT button on desired speed.

 

 

Scroll down to MENU BACK and press ENT three times to exit. 

 

b)

 

Acc/Dec 

 

Press ENT and start to select the following:-

 

 

ACC= (Accelerating distance in mm) press ENT and an arrow will appear next to ACC=.

 

 

Select the distance from Min. 50MM to Max. 500mm

 

 

Press ENT button on desired distance.

 

 

Scroll down to DEC= and press ENT and an arrow will appear next to DEC=.

 

 

Select with UP or Down buttons the required distance from Min. 300MM to Max. 990mm.

 

 

Press ENT button on desired distance.

 

 

Scroll down to NORM CLOSE or POS CLOSE (Presently not in use), press ENT to select 

the required CLOSE.

 (Select at present only NORM CLOSE)

 

a)

 

Norm Close, Gate must not bump in close or open position. (+- 15 – 20 mm Gap)

 

 

Summary of Contents for 600 Elite




















Reviews: