background image

Revision 19.1 

SOLO7 Transmitter User Guide 

 

 

Copyright © 2013 Domo Tactical Communications (DTC) Limited. All rights reserved. 

Commercial in Confidence 

Page 10-65 

 

Definition 

MPEG 

Moving Pictures Experts Group is an organisation that sets the standards for 
audio and video compression and transmission. 

Modulation 

To change the output of a transmitter in amplitude, phase or frequency in 
accordance with the information to be transmitted. Data is superimposed on 
a carrier current or wave by means of a process called modulation. 

Multicast 

Multicasting is sending data from a sender to multiple receivers where each 
receiver signals that they want to receive the data. 

 

Definition 

NLOS 

Non-line-of-sight propagation refers to RF transmissions that travel in a 
path obstructed by physical objects. 

NTSC 

National Television Systems Committee is the analogue television system 
used mainly, but not exclusively, in the Americas. 

Noise 

Unwanted disturbance in an electrical signal. 

 

Definition 

Omnidirectional antenna  An antenna whose radiation pattern shows equal radiation in all horizontal 

directions. 

 

Definition 

PAL 

Phase Alternate Line is the analogue television system used mainly, but not 
exclusively, throughout the world (see NTSC). 

PTZ 

Pan-tilt-zoom is a common way of referring to controllable cameras. 

 

Definition 

QAM 

Quadrature Amplitude Modulation. DTC products commonly use either the 16 
state (16-QAM) or 64 state (64-QAM) modulation schemes 

QPSK 

Quadrature Phase Shift Keying digital modulation scheme. 

 

Summary of Contents for SOLO7 Series









































































Reviews: