DSE DM-WFC2 Installation Manual Download Page 3 | Manualshive

Page: 3 / 15

DSE DM-WFC2 Installation Manual Download Page 3

INSTALLATION MANUAL

DM-WFC2 / 3 WFL1 - WIFI REMOTE CONTROLS

Page:3

DSE SRL - ITALY - WWW.DSE.EU

Electrical connection
DM-WFC2

DM-WFC2 is a switch with stable ON / OFF switching, remote controlled via wifi. You can use
it to supply power to any 220V up to 10A electrical appliance, such as lighting, acoustic
indicators, irrigation, etc. It also has a switch input to be able to operate parallel to a
traditional local control. In this way you can operate the device indifferently via the app with
wifi or with the local switch.

CONNECTION WITHOUT LOCAL SWITCH
LN = Connect the 110-250V AC power supply
Loutput-Noutput = Connect the AC power supply of the device to be controlled

CONNECTION WITH LOCAL SWITCH
LN = Connect the 110-250V AC power supply
Loutput-Noutput = Connect the AC power supply of the device to be controlled. This output
supplies the output voltage.
S1-S2 = Connect the local switch

You can install the module in a junction box or directly in the switch box 503 as in this example.
If you use a very small box you can remove the side flaps with the fixing holes using pliers.

«
1
2
3
4
5
...
»

Summary of Contents for DM-WFC2
















Reviews:

No comments