WARNING
Please Read Carefully
Note to Installers
This warning contains vital information. As the only individual in
contact with system users, it is your responsibility to bring each
item in this warning to the attention of the users of this system.
System Failures
This system has been carefully designed to be as effective as
possible. There are circumstances, however, involving fire,
burglary, or other types of emergencies where it may not pro-
vide protection. Any alarm system of any type may be com-
promised deliberately or may fail to operate as expected for a
variety of reasons. Some but not all of these reasons may be:
■
■
■
■
■
Inadequate Installation
A security system must be installed properly in order to pro-
vide adequate protection. Every installation should be evalu-
ated by a security professional to ensure that all access points
and areas are covered. Locks and latches on windows and doors
must be secure and operate as intended. Windows, doors, walls,
ceilings and other building materials must be of sufficient
strength and construction to provide the level of protection ex-
pected. A reevaluation must be done during and after any con-
struction activity. An evaluation by the fire and/or police de-
partment is highly recommended if this service is available.
■
■
■
■
■
Criminal Knowledge
This system contains security features which were known to
be effective at the time of manufacture. It is possible for per-
sons with criminal intent to develop techniques which reduce
the effectiveness of these features. It is important that a secu-
rity system be reviewed periodically to ensure that its features
remain effective and that it be updated or replaced if it is found
that it does not provide the protection expected.
■
■
■
■
■
Access by Intruders
Intruders may enter through an unprotected access point, cir-
cumvent a sensing device, evade detection by moving through
an area of insufficient coverage, disconnect a warning device,
or interfere with or prevent the proper operation of the system.
■
■
■
■
■
Power Failure
Control units, intrusion detectors, smoke detectors and many
other security devices require an adequate power supply for
proper operation. If a device operates from batteries, it is pos-
sible for the batteries to fail. Even if the batteries have not
failed, they must be charged, in good condition and installed
correctly. If a device operates only by AC power, any interrup-
tion, however brief, will render that device inoperative while it
does not have power. Power interruptions of any length are
often accompanied by voltage fluctuations which may damage
electronic equipment such as a security system. After a power
interruption has occurred, immediately conduct a complete
system test to ensure that the system operates as intended.
■
■
■
■
■
Failure of Replaceable Batteries
This system’s wireless transmitters have been designed to pro-
vide several years of battery life under normal conditions. The
expected battery life is a function of the device environment,
usage and type. Ambient conditions such as high humidity,
high or low temperatures, or large temperature fluctuations may
reduce the expected battery life. While each transmitting de-
vice has a low battery monitor which identifies when the bat-
teries need to be replaced, this monitor may fail to operate as
expected. Regular testing and maintenance will keep the sys-
tem in good operating condition.
■
■
■
■
■
Compromise of Radio Frequency
(Wireless) Devices
Signals may not reach the receiver under all circumstances which
could include metal objects placed on or near the radio path or
deliberate jamming or other inadvertent radio signal interfer-
ence.
■
■
■
■
■
System Users
A user may not be able to operate a panic or emergency switch
possibly due to permanent or temporary physical disability,
inability to reach the device in time, or unfamiliarity with the
correct operation. It is important that all system users be trained
in the correct operation of the alarm system and that they know
how to respond when the system indicates an alarm.
■
■
■
■
■
Smoke Detectors
Smoke detectors that are a part of this system may not properly
alert occupants of a fire for a number of reasons, some of
which follow. The smoke detectors may have been improp-
erly installed or positioned. Smoke may not be able to reach
the smoke detectors, such as when the fire is in a chimney,
walls or roofs, or on the other side of closed doors. Smoke
detectors may not detect smoke from fires on another level of
the residence or building.
Every fire is different in the amount of smoke produced and
the rate of burning. Smoke detectors cannot sense all types of
fires equally well. Smoke detectors may not provide timely
warning of fires caused by carelessness or safety hazards such
as smoking in bed, violent explosions, escaping gas, improper
storage of flammable materials, overloaded electrical circuits,
children playing with matches or arson.
Even if the smoke detector operates as intended, there may be
circumstances when there is insufficient warning to allow all
occupants to escape in time to avoid injury or death.
■
■
■
■
■
Motion Detectors
Motion detectors can only detect motion within the desig-
nated areas as shown in their respective installation instruc-
tions. They cannot discriminate between intruders and intended
occupants. Motion detectors do not provide volumetric area
protection. They have multiple beams of detection and mo-
tion can only be detected in unobstructed areas covered by
these beams. They cannot detect motion which occurs be-
hind walls, ceilings, floor, closed doors, glass partitions, glass
doors or windows. Any type of tampering whether intentional
or unintentional such as masking, painting, or spraying of any
material on the lenses, mirrors, windows or any other part of
the detection system will impair its proper operation.
Passive infrared motion detectors operate by sensing changes
in temperature. However their effectiveness can be reduced when
the ambient temperature rises near or above body temperature
or if there are intentional or unintentional sources of heat in or
near the detection area. Some of these heat sources could be
heaters, radiators, stoves, barbeques, fireplaces, sunlight, steam
vents, lighting and so on.
■
■
■
■
■
Warning Devices
Warning devices such as sirens, bells, horns, or strobes may
not warn people or waken someone sleeping if there is an
intervening wall or door. If warning devices are located on a
different level of the residence or premise, then it is less likely
that the occupants will be alerted or awakened. Audible warn-
ing devices may be interfered with by other noise sources
such as stereos, radios, televisions, air conditioners or other
appliances, or passing traffic. Audible warning devices, how-
ever loud, may not be heard by a hearing-impaired person.
■
■
■
■
■
Telephone Lines
If telephone lines are used to transmit alarms, they may be out of
service or busy for certain periods of time. Also an intruder may
cut the telephone line or defeat its operation by more sophisti-
cated means which may be difficult to detect.
■
■
■
■
■
Insufficient Time
There may be circumstances when the system will operate as
intended, yet the occupants will not be protected from the
emergency due to their inability to respond to the warnings
in a timely manner. If the system is monitored, the response
may not occur in time to protect the occupants or their be-
longings.
■
■
■
■
■
Component Failure
Although every effort has been made to make this system as
reliable as possible, the system may fail to function as in-
tended due to the failure of a component.
■
■
■
■
■
Inadequate Testing
Most problems that would prevent an alarm system from op-
erating as intended can be found by regular testing and main-
tenance. The complete system should be tested weekly and
immediately after a break-in, an attempted break-in, a fire, a
storm, an earthquake, an accident, or any kind of construc-
tion activity inside or outside the premises. The testing should
include all sensing devices, keypads, consoles, alarm indicat-
ing devices and any other operational devices that are part of
the system.
■
■
■
■
■
Security and Insurance
Regardless of its capabilities, an alarm system is not a substi-
tute for property or life insurance. An alarm system also is
not a substitute for property owners, renters, or other occu-
pants to act prudently to prevent or minimize the harmful
effects of an emergency situation.
FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your
authority to use this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Re-orient the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
The user may find the following booklet prepared by the FCC useful: “How to Identify and Resolve Radio/Television
Interference Problems”. This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402,
Stock # 004-000-00345-4.
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules. On the side of this equipment is a label that contains, among
other information, the FCC registration number of this equipment.
NOTIFICATION TO TELEPHONE COMPANY The customer shall notify the telephone company of the particular
line to which the connection will be made, and provide the FCC registration number and the ringer equivalence of
the protective circuit.
FCC Registration Number: F53CAN-30678-AL-E
Ringer Equivalence Number: 0.1B
USOC Jack: RJ-31X
TELEPHONE CONNECTION REQUIREMENTS Except for the telephone company provided ringers, all
connections to the telephone network shall be made through standard plugs and telephone company provided jacks,
or equivalent, in such a manner as to allow for easy, immediate disconnection of the terminal equipment. Standard
jacks shall be so arranged that, if the plug connected thereto is withdrawn, no interference to the operation of the
equipment at the customer’s premises which remains connected to the telephone network shall occur by reason of such
withdrawal.
INCIDENCE OF HARM Should terminal equipment or protective circuitry cause harm to the telephone network,
the telephone company shall, where practicable, notify the customer that temporary disconnection of service may be
required; however, where prior notice is not practicable, the telephone company may temporarily discontinue service
if such action is deemed reasonable in the circumstances. In the case of such temporary discontinuance, the telephone
company shall promptly notify the customer and will be given the opportunity to correct the situation.
ADDITIONAL TELEPHONE COMPANY INFORMATION The security control panel must be properly
connected to the telephone line with a USOC RJ-31X telephone jack.
The FCC prohibits customer-provided terminal equipment be connected to party lines or to be used in conjunction
with coin telephone service. Interconnect rules may vary from state to state.
CHANGES IN TELEPHONE COMPANY EQUIPMENT OR FACILITIES The telephone company may make
changes in its communications facilities, equipment, operations or procedures, where such actions are reasonably
required and proper in its business. Should any such changes render the customer’s terminal equipment incompatible
with the telephone company facilities the customer shall be given adequate notice to the effect modifications to
maintain uninterrupted service.
RINGER EQUIVALENCE NUMBER (REN) The REN is useful to determine the quantity of devices that you may
connect to your telephone line and still have all of those devices ring when your telephone number is called. In most,
but not all areas, the sum of the RENs of all devices connected to one line should not exceed five (5.0). To be certain
of the number of devices that you may connect to your line, you may want to contact your local telephone company.
EQUIPMENT MAINTENANCE FACILITY If you experience trouble with this telephone equipment, please
contact the facility indicated below for information on obtaining service or repairs. The telephone company may ask
that you disconnect this equipment from the network until the problem has been corrected or until you are sure that
the equipment is not malfunctioning.
Digital Security Controls Ltd. 160 Washburn St., Lockport, NY 14094
