Security Products
TM
©1998 Digital Security Controls Ltd.
1645 Flint Road, Downsview, Ontario, Canada M3J 2J6
(416) 665-8460 • Fax (416) 665-7498 • 1-800-387-3630
Printed in Canada 29002894 R1
For more information regarding module enrollment, see the
control panel Installation Manual.
5.
Programming the Module
To access PC4010/PC4020 programming, enter [*][8] followed
by the Installer’s code. Program the sections indicated on this
worksheet, and record your programming choices in the space
provided. The waterflow and 2-wire smoke zones are hard-coded
and the zone type cannot be changed. Refer to your Commercial
Fire Installation Guide for more information on PC4701 zones.
If the
2-wire smoke auto-verify
feature is enabled in the System
Toggles section (ref. # [000200]), the panel will automatically
verify alarms from the 2-wire smoke circuit of the PC4701 before
INDUSTRY CANADA NOTICE
NOTICE: The Industry Canada label identifies certified equipment. This certification
means that the equipment meets certain telecommunications network protective, operational
and safety requirements. Industry Canada does not guarantee the equipment will operate to
the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected
to the facilities of the local telecommunications company. The equipment must also be
installed using an acceptable method of connection. The customer should be aware that
compliance with the above conditions may not prevent degradation of service in some
situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance
facility designated by the supplier. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions, may give the telecommunications company cause
to request the user to disconnect the equipment.
User should ensure for their own protection that the electrical ground connections of the
power utility, telephone lines and internal metallic water pipe system, if present, are
connected together. This precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should
contact the appropriate electric inspection authority, or electrician, as appropriate.
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device
provides an indication of the maximum number of terminals allowed to be connected to
a telephone interface. The termination on an interface may consist of any combination of
devices subject only to the requirement that the sum of the Ringer Equivalence Number
of all the devices does not exceed 5.
The REN of this unit is 0.0.
AVIS: L’étiquette de l’Industrie Canada identifie le matériel homologué. Cette étiquette
certifie que le matériel est conforme à certaines normes de protection, d’exploitation et de
sécurité des réseaux de télécommunications. Industrie Canada n’assure toutefois pas que
le matériel fonctionnera à la satisfaction de l’utilisateur.
Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux
installations de l’entreprise locale de télécommunication. Le matériel doit également être
installé en suivant une méthode acceptée de raccordement. L’abonné ne doit pas oublier
qu’il est possible que la conformité aux conditions énoncées ci-dessus n’empêchent pas la
dégradation du service dans certaines situations.
Les réparations de matériel homologué doivent être effectuées par un centre d’entretien
canadien autorisé désigné par le fournisseur. La compagnie de télécommunications peut
demander à l’utilisateur de débrancher un appareil à la suite de réparations ou de
modifications effectuées par l’utilisateur ou à cause de mauvais fonctionnement.
Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre de
la source d’énergie électrique, les lignes téléphoniques et les canalisations d’eau métalliques,
s’il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans
les régions rurales.
AVERTISSEMENT: L’utilisateur ne doit pas tenter de faire ces raccordements lui-
même; il doit avoir recours à un service d’inspection des installations électriques, ou à
un électricien, selon le cas.
AVIS: L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif terminal
indique le nombre maximal de terminaux qui peuvent être raccordés à une interface. La
terminaison d’une interface téléphonique peut consister en une combinaison de quelques
dispositifs, à la seule condition que la somme d’indices d’équivalence de la sonnerie de
tous les dispositifs n’excède pas 5.
L’indice d’équivalence de la sonnerie (IES) de ce produit est 0.0.
Please refer to your PC4010/PC4020 Installation Manual for information on how to program.
[0001]
Event Messages
[000102]
2-Wire Smoke
I______I______I______I______I______I______I______I______I______I______I______I______I______I______I______I______I
[000103]
Waterflow
I______I______I______I______I______I______I______I______I______I______I______I______I______I______I______I______I
[000200]
System Toggle Options:
scroll to
2WS AutoVerify
Default: N
I________I
[00020311]
Waterflow Delay
Default: 000
I______I______I______I
Valid entries are 000-090 seconds.
NOTE
: If a waterflow delay is programmed, the PC4701 waterflow zone follows it. Please see your PC4010CF/4020CF Installation
Guide for more details.
[000403]
Reporting Codes
[00040309]
Fire Events
2 Wire Alarm
I______I______I
2 Wire Trouble
I______I______I
Fire Test Begin
I______I______I
2 Wire Restore
I______I______I
2 Wire TBL Rest.
I______I______I
Fire Test End
I______I______I
Waterflow Alarm
I______I______I
Waterflow TBL
I______I______I
Fire Bypass
I______I______I
Waterflow Rest.
I______I______I
Waterflw TBL Rest
I______I______I
Fire Unbypass
I______I______I
FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Digital Security
Controls Ltd. could void your authority to use this equipment.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
n
Re-orient the receiving antenna.
n
Increase the separation between the equipment and receiver.
n
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
n
Consult the dealer or an experienced radio/television technician for help.
The user may find the following booklet prepared by the FCC useful: “How to Identify
and Resolve Radio/Television Interference Problems”. This booklet is available from
the U.S. Government Printing Office, Washington D.C. 20402, Stock # 004-000-
00345-4.
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules. On the side of this
equipment is a label that contains, among other information, the FCC registration
number of this equipment.
NOTIFICATION TO TELEPHONE COMPANY The customer shall notify the
telephone company of the particular line to which the connection will be made,
and provide the FCC registration number and the ringer equivalence of the
protective circuit.
FCC Registration Number:
F53CAN-32904-AL-N
Ringer Equivalence Number:
0.0B
USOC Jack:
RJ31X
TELEPHONE CONNECTION REQUIREMENTS
Except for the telephone company
provided ringers, all connections to the telephone network shall be made through
standard plugs and telephone company provided jacks, or equivalent, in such a
manner as to allow for easy, immediate disconnection of the terminal equipment.
Standard jacks shall be so arranged that, if the plug connected thereto is withdrawn,
no interference to the operation of the equipment at the customer’s premises which
remains connected to the telephone network shall occur by reason of such withdrawal.
INCIDENCE OF HARM
Should terminal equipment or protective circuitry cause
harm to the telephone network, the telephone company shall, where practicable,
notify the customer that temporary disconnection of service may be required;
however, where prior notice is not practicable, the telephone company may temporarily
discontinue service if such action is deemed reasonable in the circumstances. In the
case of such temporary discontinuance, the telephone company shall promptly
notify the customer and will be given the opportunity to correct the situation.
ADDITIONAL TELEPHONE COMPANY INFORMATION
The security control panel
must be properly connected to the telephone line with a USOC RJ-31X telephone
jack.
The FCC prohibits customer-provided terminal equipment be connected to party
lines or to be used in conjunction with coin telephone service. Interconnect rules may
vary from state to state.
CHANGES IN TELEPHONE COMPANY EQUIPMENT OR FACILITIES
The
telephone company may make changes in its communications facilities, equipment,
operations or procedures, where such actions are reasonably required and proper
in its business. Should any such changes render the customer’s terminal equipment
incompatible with the telephone company facilities the customer shall be given
adequate notice to the effect modifications to maintain uninterrupted service.
RINGER EQUIVALENCE NUMBER (REN)
The REN is useful to determine the
quantity of devices that you may connect to your telephone line and still have all of
those devices ring when your telephone number is called. In most, but not all areas,
the sum of the RENs of all devices connected to one line should not exceed five (5.0).
To be certain of the number of devices that you may connect to your line, you may
want to contact your local telephone company.
EQUIPMENT MAINTENANCE FACILITY
If you experience trouble with this telephone
equipment, please contact the facility indicated below for information on obtaining
service or repairs. The telephone company may ask that you disconnect this
equipment from the network until the problem has been corrected or until you are
sure that the equipment is not malfunctioning.
Digital Security Controls Ltd. 160 Washburn St., Lockport, NY 14094
sounding the bells and transmitting the alarms.
Verification will function as follows: when the 2-wire smoke
circuit is shorted, the PC4701 performs a sensor reset by removing
power from the circuit for 20 seconds. After the 20 second reset,
power will be restored to the circuit and troubles will be bypassed
for 10 seconds to allow detectors to settle. If the smoke detectors
inititate another alarm within 60 seconds after power is restored,
a fire alarm will be generated immediately. If the smoke detector
is not reset by the power down, the zone will not be restored. If
this occurs, the panel will initiate a fiire alarm immediately (30
seconds after initial alarm).
If the feature is disabled, the panel will generate fire alarms
instantly.
