c) Buzzer Control: There are 15 different buzzer control levels. Use the [<][>] keys
to scroll to the desired contrast level.
Keypad LED Symbols
Proximity Tags (HS2LCDWFP, HS2LCDWFPV only)
The proximity tag can be used to perform any keypad function that would nor-
mally require a user access code. The tag is to be presented to the face of the
keypad. While the keypad is running off AC, the transceiver is always on to
detect any prox tag approaching. While the keypad is running on battery and in
sleep mode, the user can press any key to wake the keypad, then present the
prox tag.
Enrolling Proximity Tags
Enrolling a tag on one keypad will enroll it automatically to all HS2LCDWFP
or HS2LCDWFPV
keypads enrolled on the system.
1. Enter [
][5] and an access code with the supervisor attribute enabled.
2. Select or enter a two-digit User Code slot (02-95) to be associated with the
proximity tag. Alternatively, scroll to the two-digit user number and press
the [
]
key.
3. Scroll to ‘Press [
] for Prox Tag’ and press the [
] key.
4. The screen will prompt “Present Your Prox Tag”; do so or press the [#] key
to exit.
5. Present your proximity tag to the keypad. If enrollment is successful,
acknowledgement beeps will sound and the keypad LCD will read ‘Tag
Enrolled Successfully’. If enrollment is unsuccessful, an error tone will
sound and the keypad will read ‘Invalid Tag Not Enrolled’. If the tag has
been enrolled previously, an error tone will sound.
Deleting Proximity Tags
Delete the prox tags from the system when they are lost or no longer needed.
1. Enter [
][5] and an access code with the supervisor attribute enabled.
2. The keypad will display the user number and include the letter ‘T’ if a prox
tag is programmed.
3. Scroll to ‘Press [
] for Prox Tag’ and press the [
] key.
4. The keypad will read ‘Press [
] To Delete Tag’.
5.After pressing [
], the message ‘Tag Deleted Successfully’ appears.
NOTE: User codes can only be deleted individually.
NOTE: User 01 - Master Code cannot be deleted; a deletion attempt on this user code will
delete the proximity tag only.
NOTE: A user code, once deleted, must be re-enrolled before it can be used again.
Keypad Function Key Programming
To program a function key:
1. Enter Installer Programming by entering [
][8][Installer Code].
2. Press [861] for keypad programming. Section [860] is read-only and shows
the slot number of the keypad being accessed.
3. Enter [001]-[005] for function keys 1-5.
4. Enter a 2-digit number to assign a function key operation - [00]-[68]. See
table below.
5. Continue from step 3 until all function keys are programmed.
6. Press the [#] key twice to exit Installer Programming.
[001]-[005] Function Key Assignment
Symbol
Description
Ready Light (Green)
If Ready light is ON, the system is ready to arm.
Armed Light (Red)
If Armed light is ON/Flashing, the system has
been armed successfully.
System Trouble (Yellow) ON - Indicates that a system trouble is active.
Flashing - Keypad low battery.
AC (Green)
ON - Indicates that AC is present at the keypad.
Section Function
Key
Button Valid
Range Default Function
[001]
1
00 - 68
03
Stay Arm
I_______I_______I
[002]
2
00 - 68
04 Away Arm I_______I_______I
[003]
3
00 - 68
01
Disarm
I_______I_______I
[004]
4
00 - 68
52
[P] Key
Alarm
I_______I_______I
[005]
5
00 - 68
16
Quick
Exit
I_______I_______I
