FCC Compliance Statement
CAUTION: Changes or modifications not expressly approved by Digital
Security Controls could void your authority to use this equipment.
This
equipment generates and uses radio frequency energy and if not installed
and used properly, in strict accordance with the manufacturer's instructions,
may cause interference to radio and television reception. It has been type
tested and found to comply with the limits for Class B device in accordance
with the specifications in Subpart "B" of Part 15 of FCC Rules, which are
designed to provide reasonable protection against such interference in any
residential insta llation. However, the re is no gua rantee tha t inte rference
will n ot occur in a partic ular installation. If th is equipment does c ause
interference to te levision or radio reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Re-orient the receiving antenna
• Relocate the alarm control with respect to the receiver
• Move the alarm control away from the receiver
• Connect the alarm control into a different outlet so that alarm control and
receiver are on different circuits.
If necessary, the user should consult the dealer or an experienced radio/
television tec hnician f or additional suggestions. The us er ma y find the
following bo oklet pr epared by the FCC helpful: "H ow to Identify and
Resolve Radio/Television Interference Problems". This booklet is available
from the U.S. Government Printing Office, Washington, D.C. 20402, Stock
# 004-000-00345-4.
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules. On the side of this
equipment is a label th at contains, am ong other inf ormation, the FC C
registration n umber a nd r inger eq uivalence nu mber ( REN) f or th is
equipment. If requested, this n umber must be provided to the Tele phone
Company.
GS3125 Product IdentifierUS: F53MO00BGS3125
REN:0.0B
USOC Jack:RJ-31X
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and
requirements ad opted by t he A CTA. A com pliant telephone cord and
modular plug is provided with this product. It is designed to be connected
to a com patible m odular jack that is also compliant. S ee in stallation
instructions for details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be connected
to a telephone line. Excessive RENs on a telephone line may result in the
devices not ringing in response to an incoming call.
In most but not all areas, the sum of RENs should not exceed five (5.0). To
be certain of the number of devices that may be connected to a line, as
determined by the total RENs, contact the local Telephone Company. For
products approved after July 23, 2001, the REN for this product is part of
the product identifier that has th e fo rmat. US: A AAEQ##TXXXX. The
digits represented by ## are the REN without a decimal point (e.g., 03 is a
REN of 0.3). For earlier products, the REN is separately shown on the label.
Incidence of Harm
If this equipment GS3125 causes harm to the telephone network, the
telephone c ompany w ill n otify y ou in a dvance that tem porary
discontinuance of service may be required. But if advance notice is not
practical, the Tele phone Company w ill no tify th e custom er as soon as
possible. Also, you will be advised of your right to file a complaint with the
FCC if you believe it is necessary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment,
operations or procedures that could affect the operation of the equipment.
If t his happens the Te lephone Com pany will p rovide advance no tice in
order for you to make necessary modifications to m aintain uninterrupted
service.
Equipment Maintenance Facility
If tr ouble is e xperienced w ith t his eq uipment f or r epair or w arranty
information, please contact the facility indicated below. If the equipment is
causing ha rm to the tele phone network, the Tel ephone Company ma y
request that you disconnect the equipment until the problem is solved. This
equipment is of a type that is not intended to be repaired by the end user.
DSC c/o APL Logistics, 757 Douglas Hill Rd., Lithia Springs, GA 30122
Additional Information
Connection to party line service is subject to state tariffs. Contact the state
public uti lity com mission, pub lic se rvice com mission or corporation
commission for information.
Alarm dialling equipment must be able to seize the telephone line and place
a call in an emergency situation. It m ust be able to d o this even if oth er
equipment (telephone, answering system, computer modem, etc.) already
has the telephone line in use. To do so, alarm dialling equipment must be
connected to a properly installed RJ-31X jack that is electrically in series
with and ahead of all other equipment attached to the same telephone line.
Proper installation is depicted in the figure below. If you have any questions
concerning these instructions, you should consult your telephone company
or a qualified installer about installing the RJ-31X jack and alarm dialling
equipment fo
r
you.
Industry Canada Compliance Statement
This Equipment meets the applicable Industry Canada Terminal Equipment
Technical Specifications. This is confirmed by the registration number. The
abbreviation, IC, before the registration number signifies that registration
was pe rformed bas ed on a D eclaration of C onformity i ndicating that
Industry Canada technical specifications were met. It does not imply that
that I ndustry Canada app roved the equipment. The Ringer Equiv alence
Number (REN) for this terminal equipment is 0 .0. The REN assigned to
each terminal equipment provides an indication of the maximum number of
terminals allowed to be connected to a telephone interface. The termination
on an interface may consist of any combination of devices subject only to
the requirement that the s um of t he Ringer Equivalence Numbers of all
devices does not exceed 5.
Cet équipement est conforme aux spécifications techniques applicables aux
équipements ter minaux d' Industrie C anada. Ce ci e st co nfirmé pa r le
numéro d'enregistrement. L' abréviation IC p
récédant le n
uméro
d'enregistrement signifie que l'enregistrement a été effectué sur la base de
la Déclaration de conformité indiquant que le produit es t conforme aux
spécifications techniques d'Industrie Canada. Ceci n'implique pas que le
produit ait été approuvé par Industrie Canada.
Le nombre équivalent de sonneries (REN) de cet appareil terminal est 0.0.
Le REN attribué à chaque équipement terminal fournit une indication sur le
nombre maximum de terminaux pouvant être connectés sur une interface
téléphonique. La terminaison sur une interface peut constituer en n'importe
quelle combinaison d'appareils, à la condition seulement que la somme des
Nombres é quivalents de s onneries de tous le s a ppareils ne s oit pa s
supérieure à 5.
This Clas s B dig ital app aratus m eets all re quirements of the Ca nadian
interference-causing equipment regulations. Cet appareil numérique de la
Classe B r especte toutes les e xigences de rè glement sur le m atériel
brouilleur du Canada.
The term “IC:” before the radio certification number only signifies
that Industry Canada technical specifications were met.
Telephone
Comp
u
ter
Telephone
Telephone
F
a
x M
a
chine
Al
a
rm Di
a
ling
Eq
u
ipment
RJ-
3
1X
J
a
ck
Un
us
ed
RJ-11 J
a
ck
Telephone
Line
Network
Service
Provider'
s
F
a
cilitie
s
C
us
tomer Premi
s
e
s
Eq
u
ipment
a
nd Wiring
Un
us
ed
RJ-11 J
a
ck
Network
Dem
a
rc
a
tion
Point
An
s
wering
Sy
s
tem
WARNING: To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 20cm
or more must be maintained between the antenna of this device and persons during device operation.
